Index, Introduction, Operating Modes | American Panel AP24BC250-3

Image 2

American Panel AP24BC250-3 Index, Introduction, Controller Features, Operating Modes, Automatic Mode, Manual Mode, Panning

Contents

E-mail service@americanpanel.com American Panel CorporationREV. E USER’S MANUAL REQUIREMENTS TO BE MET DURING INSTALLATION 8 STEPS CONTROLLER FEATURESINSTALLATION OF REMOTE UNITS INSTALLATION AT THE SAME LEVEL MAINTENANCE AND CLEANING PREPARING AND USING THE OPTIONAL PRINTERMAINTENANCE CLEANING THE CONDENSER OPERATING MODES CONTROLLER FEATURESINTRODUCTION PC CONNECTION OPTIONAL OPERATING CYCLESPRINTER OPTIONAL INSTALLATION AT THE SAME LEVEL INSTALLATION OF REMOTE UNITSREQUIREMENTS TO BE MET DURING INSTALLATION 8 STEPS COMPRESSOR INSTALLATION AT DIFFERENT LEVELS CONNECTION PIPING FOR REMOTE CONDENSING UNITS DIMENSIONS INSTALLATIONINSTALLATION WARNINGS CONNECTION TO THE REMOTE UNIT VERIFYING CORRECT INSTALLATIONELECTRICAL AND REFRIGERATION SPECIFICATIONS CONDENSATE DRAINAGE CONNECTION STARTING & TESTING THE UNIT SPACES AROUND THE CABINET SHOCK FREEZING USING THE HURRICHILL TECHNOLOGYBLAST CHILLING SOFT CHILL CYCLE LOADING PANNING AND LOADINGPANNING CONTROL PANEL FOR MODELS AP24 & AP40 BLAST CHILLERS / SHOCK FREEZERS ON/OFF & START/STOP KEYBOARD KEYSKEY COMBINATIONS PROGRAMMING KEYS PROGRAMMING c. Enter the default password by pressing, in order, theIf the entered password is wrong the display will show 1. INITIAL PROGRAMMING The high food alarm temperature should be left at The high air alarm temperature should be left atThe low air alarm temperature should be left at YES for shock freezers AP24BCF300-3, AP40BCF450-3 The low food alarm temperature should be left atThe P.C. baud rate should be left at NO for blast chillers AP24BC250-3, AP40BC350-3 and go to step r 2. PROGRAMMING THE CYCLES AUTOMATIC SOFT CYCLE PARAMETERS PROGRAMMING AUTOMATIC HARD CYCLE PARAMETERS PROGRAMMING then press AUTOMATIC SHOCK CYCLE PARAMETERS PROGRAMMINGk. To change the temperature, press p. To change the temperature, press UV LIGHT CYCLE PARAMETERS PROGRAMMING The defrost type must be left AIR FLOW DEFROST CYCLE PARAMETERS PROGRAMMINGHEATED PROBE CYCLE PARAMETERS PROGRAMMING aa. Press The LED for SOFT will be steady MANUAL SOFT CYCLE PARAMETERS PROGRAMMINGgg. Press hh. To change the temperature, press MANUAL HARD CYCLE PARAMETERS PROGRAMMING MANUAL SHOCK CYCLE PARAMETERS PROGRAMMING 3. RECIPE NAME PROGRAMMING OPERATION 1. AUTOMATIC MODE - SOFT CHILL alternating 2. MANUAL MODE - SOFT CHILLalternating with 3. HARD CHILL CYCLE 6. DEFROST CYCLE 4. SHOCK FREEZE CYCLE5. UV STERILIZATION CYCLE a. To perform a UV cycle remove all food, then press c. Press the 7. HEATED FOOD PROBEb. Open the door defrost cycle 8. PREPARING AND USING THE OPTIONAL PRINTER OTE To stop any cycle before it has finished, press START/STOP PRINTER d. Enter your password, then pressNOTE The optional printer is delivered fully installed 9. TO CLEAR DATA REMOVING A ROLL OF PAPER MAINTENANCELOADING A ROLL OF PAPER OPERATING THE PRINTER REPLACING THE RIBBON WITH PAPER IN THE PRINTER MAINTENANCE AND CLEANINGCLEANING THE CONDENSER COMPARTMENT WIRING DIAGRAMSCLEANING DO NOT USE ABRASIVES, SOLVENTS AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual COMPUTER CONNECTION DESCRIPTION PARTS LISTPART # AMERICAN PANEL CORP STANDARD WARRANTYinstalling contractor. It is not covered by this Warranty BLAST CHILLERS / SHOCK FREEZERS ONLY ORDERING PRINTER SUPPLIES RIBBON & PAPER