American Panel AP24BC250-3 specification

Image 32

American Panel AP24BC250-3 user manual Preparing And Using The Optional Printer

Contents

American Panel Corporation REV. EE-mail service@americanpanel.com USER’S MANUAL CONTROLLER FEATURES INSTALLATION OF REMOTE UNITSREQUIREMENTS TO BE MET DURING INSTALLATION 8 STEPS INSTALLATION AT THE SAME LEVEL PREPARING AND USING THE OPTIONAL PRINTER MAINTENANCEMAINTENANCE AND CLEANING CLEANING THE CONDENSER OPERATING MODES CONTROLLER FEATURESINTRODUCTION PC CONNECTION OPTIONAL OPERATING CYCLESPRINTER OPTIONAL INSTALLATION OF REMOTE UNITS REQUIREMENTS TO BE MET DURING INSTALLATION 8 STEPSINSTALLATION AT THE SAME LEVEL COMPRESSOR INSTALLATION AT DIFFERENT LEVELS CONNECTION PIPING FOR REMOTE CONDENSING UNITS INSTALLATION INSTALLATIONDIMENSIONS WARNINGS VERIFYING CORRECT INSTALLATION ELECTRICAL AND REFRIGERATION SPECIFICATIONSCONNECTION TO THE REMOTE UNIT CONDENSATE DRAINAGE CONNECTION STARTING & TESTING THE UNIT SPACES AROUND THE CABINET USING THE HURRICHILL TECHNOLOGY BLAST CHILLINGSHOCK FREEZING SOFT CHILL CYCLE LOADING PANNING AND LOADINGPANNING CONTROL PANEL FOR MODELS AP24 & AP40 BLAST CHILLERS / SHOCK FREEZERS KEYBOARD KEYS KEY COMBINATIONSON/OFF & START/STOP PROGRAMMING KEYS c. Enter the default password by pressing, in order, the If the entered password is wrong the display will showPROGRAMMING 1. INITIAL PROGRAMMING The high food alarm temperature should be left at The high air alarm temperature should be left atThe low air alarm temperature should be left at The low food alarm temperature should be left at The P.C. baud rate should be left atYES for shock freezers AP24BCF300-3, AP40BCF450-3 NO for blast chillers AP24BC250-3, AP40BC350-3 and go to step r 2. PROGRAMMING THE CYCLES AUTOMATIC SOFT CYCLE PARAMETERS PROGRAMMING AUTOMATIC HARD CYCLE PARAMETERS PROGRAMMING AUTOMATIC SHOCK CYCLE PARAMETERS PROGRAMMING k. To change the temperature, pressthen press p. To change the temperature, press UV LIGHT CYCLE PARAMETERS PROGRAMMING DEFROST CYCLE PARAMETERS PROGRAMMING HEATED PROBE CYCLE PARAMETERS PROGRAMMINGThe defrost type must be left AIR FLOW aa. Press MANUAL SOFT CYCLE PARAMETERS PROGRAMMING gg. PressThe LED for SOFT will be steady hh. To change the temperature, press MANUAL HARD CYCLE PARAMETERS PROGRAMMING MANUAL SHOCK CYCLE PARAMETERS PROGRAMMING 3. RECIPE NAME PROGRAMMING OPERATION 1. AUTOMATIC MODE - SOFT CHILL alternating 2. MANUAL MODE - SOFT CHILLalternating with 3. HARD CHILL CYCLE 4. SHOCK FREEZE CYCLE 5. UV STERILIZATION CYCLE6. DEFROST CYCLE a. To perform a UV cycle remove all food, then press 7. HEATED FOOD PROBE b. Open the doorc. Press the defrost cycle 8. PREPARING AND USING THE OPTIONAL PRINTER OTE To stop any cycle before it has finished, press START/STOP d. Enter your password, then press NOTE The optional printer is delivered fully installedPRINTER 9. TO CLEAR DATA MAINTENANCE LOADING A ROLL OF PAPERREMOVING A ROLL OF PAPER OPERATING THE PRINTER REPLACING THE RIBBON WITH PAPER IN THE PRINTER MAINTENANCE AND CLEANINGCLEANING THE CONDENSER WIRING DIAGRAMS CLEANINGCOMPARTMENT DO NOT USE ABRASIVES, SOLVENTS AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual COMPUTER CONNECTION DESCRIPTION PARTS LISTPART # STANDARD WARRANTY installing contractor. It is not covered by this WarrantyAMERICAN PANEL CORP BLAST CHILLERS / SHOCK FREEZERS ONLY ORDERING PRINTER SUPPLIES RIBBON & PAPER