Manuals / AMT Datasouth / Computer Equipment / All in One Printer

AMT Datasouth 4600 manual Appendix E Adjusting Ribbon Tension

Models: 4600

1 91

Page 89

Appendix E: Adjusting Ribbon Tension

The ribbon shaft has its user-friendly feature to allow users to adjust the tension of ribbon shaft by rotating the knob. User can reset to factory default tension by adjusting the ribbon shaft while the black line was aligned to the marked arrows.

Appendix F: Switching Ribbon Wound Ink-side out or Ink-side in

The printer is produced to suit flexible applications, no matter with ribbon wound ink-side in (manufacturing default), or with ribbon wound ink-side out. The steps to switch are listed as follows:

1. Pull and move the SHAFT RIBBON ADJ into the Inside:

Page 89

Image 89

AMT Datasouth 4600 Appendix E Adjusting Ribbon Tension, Appendix F Switching Ribbon Wound Ink-side out or Ink-side in

Contents

Thermal Transfer Barcode Printer User’s GuideFastmark 4600 PLUS Series Table of Contents Technical Reference Table of ContentsTRADEMARK CREDITS IMPORTANT SAFETY INSTRUCTIONS AND OTHER NOTICESUnpacking Getting Started2. Installation Quick Start Guide Package Contents3. CD Rom User Guides, Utility Software & Drivers 4. AC Power Cord 1. Fastmark 4600 PLUS Series PrinterPlacing the Printer Connecting the Power CordWARNING! Do not operate the printer in an area where it might get wet Front Panel Getting to Know Your PrinterButtons LED IndicatorsFor the FM 4602 PLUS Series, and the FM 4603 PLUS Series models, modes ofLCD Display 300,PAL/PPLZ ESC FOR KEYBD Setting Display Language203,PAL/PPLZ WITH B.C. READER 300,PAL/PPLZ WITH B.C. READERSetting Procedure Changing Settings from the Panelduring printing or communication Basic Printer Features and Parameter Settings , PPLA/PPLBNOTE Features can vary based on printer model. Do not change settings Printer Features and Parameter Settings, PAL/PPLZ Factory Default FeatureINSTALLED characteristics. OnceRibbon Pick-up Spindle Internal Parts and FeaturesRibbon Supply Spindle Media Supply Spindle Rear Feed Slot Head Latch Thermal Printhead Paper Drive RollerPeeler Option Cutter Module Front Access Loading Ribbon and MediaLoading a Ribbon Head 2. Turn the head latch counter-clockwise and open the bracket. FigureBracket Ribbon Supply6. Insert the core onto the ribbon pick-up spindle. Figure 4. Lead the ribbon through the print head module. FigureRibbon Pick-upStandard Mode Loading MediaHead outside media guide. FigureLatch Outside3. Lead the media through the print head module and under the paper sensor guide. Figure Page Remove labels Peel Off ModeBacking Paper Print Head Media Backing/LinerModule Dispenser4. Close the peeler module using the peel-off mechanism release lever. Figure Cutter Module Print Head Module Paper Sensor Guide Cutting ModeOutside Media Guide HeadFront Panel Control Panel OperationLED Indicators Buttons Pressed and held down during Power UPButton FunctionButton Pressed during normal operationFunction Pressed for Special functionsLCD Display With Keyboard Option installedStandard Printer With Barcode Reader OptionPRINT MODE DIRECT THERMAL Front Panel Set-up MenuSet-up Mode Buttons1. Power on the printer Feature Item Typical Set-up Control Panel Features features may differ amongFactory Default 2. Make sure the settings you desire has an * character by the valueLegacy Data Stream Interpretation PALTM Print and Program OverviewTraditional Printing Host System Standalone/Downtime Applications Ability to operate on line from host or off line in stand-alone mode Performing Calibration Calibration & ConfigurationPrinting a Configuration Report 3. Printed label count is not reset Resetting to Factory Default SettingsCentronics Parallel Port Computer ConnectionsUSB Interface Requirements Ethernet 10/100 Internal Printer Server Option Serial RS-232 Port1. Centronics allows a much higher communication speed than serial this cableLED Status Ethernet Module Status IndicatorsDescription BlinkingGreen LED Amber LED Ethernet LED IndicatorsCommunicating with the Printer Page 6. Click Finish TIA-230 TIA-230E TIZ-230 7. Select Install printer drivers and Click Next8. Select model & emulation 9. Select the port of the printer and click Next Not Shared LT1 YES TIA-230E 7.1.8M-0 Installed printer TIA-230E PPLB installedMedia Problems TroubleshootingNote If problem continues perform a label sensor calibration LED and LCD DiagnosisNote After problem is solved, press CANCEL to continue printing Ribbon ProblemsOther Problems Light /Missing Print Miscellaneous Recovery Note Turn off the printer before cleaning Cleaning the Print HeadCaring for Your Printer depending on actual usage and conditionsdust or adhesives Cleaning the RollerCleaning the Media Compartment Technical Reference General Specifications24lbs11kgs PAL/PPLZ PPLAPPLB Printer Programming Language A, PPLA Fonts, Bar Codes and Graphics SpecificationPrinter Programming Language B, PPLB Printer Programming Language Z, PPLZ USB series “B” Receptacle Interface Interface SpecificationsConnector Terminal Pin Assignment if you use a general host such as a PC Serial InterfaceConnection with Host Terminal/Host TxData RxData Ground Printer Pin 2- RxData ……… Pin 3- TxData ……… Pin 5- Ground ………Data format always 8 data bits, 1 start bit and 1 stop bit ParityAuto Polling Parallel CentronicsData1 Data3Signal Ethernet InterfaceASCII TABLE Appendix A Printer Status Appendix B Stand-alone Keyboard and Barcode Reader KeyboardForm Control Functions Example Making a Keyboard Form KBDFORM READY 203,PPLB ESC FOR KEYBD5. Key-in the product name and number Product Name ? Barcode Printer Product No. ? 0123456789 6. Input the label count and copy countENTER to go on Or ESC to return OutputBarcode Reader Example Making a Barcode Reader Form Product No.? 11223344 Product Name? APPLE OutputRefer to the following steps to install the cutter kit onto printers Appendix C Cutter Installation1. Turn off the printer 2. Remove the top covers on both left and right sides8. Turn on the printer 9. Set parameter “CUTTER INSTALLED”, on the LCD to the ON position5. Loosen and remove the two screws 4 from bracket 3. Turn on the printer 1. Put the media end on the roller 2. Close the TPH latch4. Press the FEED button to feed the media end through the cutter After the cutter is installed, install media and ribbonInstall a dispenser into the printer as follows Appendix D Dispenser Installation1. Turn off the printer 2. Remove the top cover on both left and right sidesPage 8. Set parameter “DISPENSER INSTALLED” on the LCD to the ON position 6. Install the ribbon and media 7. Turn on the printerAppendix F Switching Ribbon Wound Ink-side out or Ink-side in Appendix E Adjusting Ribbon Tension