APC MW II Battery cables connection

Symmetra MW II 1200 kW 3 x 400/230 V Installation - 990-1979E-0018

1. With the top covers removed, drill holes for AC, PE and Battery grommets in areas shown.

2. Re-fit the covers and install the grommets.

3. Feed AC and PE cables through grommets in the Control/Input/Output Section.

4. Connect PE cable.

5. Connect AC IN cables to normal power and bypass power.

6. Connect AC OUT cables.

Battery cables connection

Warning: Make sure that the battery breakers are open (OFF) prior to running the

cables.

Caution: For battery installation and maintenance instructions, refer to the battery

manufacturer’s installation manual.

Caution: Over-current protection for the battery circuit is required by code. The minimum

DC voltage rating of the battery supply over-current protection device is 500 V.

Note: Over-current protection for the battery circuit is required by national wiring rules.

Busbar

Hole distance AC

ﬂ 13

Cable lug

58 mm

44.45 mm

44.45 mm

Busbar

Hole distance DC

ﬂ 13

Cable lug

35.8 mm

44.45 mm

44.45 mm

Busbar

Hole distance grounding

46.99 mm

44.45 mm

44.45 mm

Cable lug

M10 stud

Contents

Main Installation Symmetra MW II Normal UPS Summary 1200 kW 400 V Page Contents Safety ............................................... .......................1 System Overview............................ ..........................3 UPS Sections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 External Bypass Static Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Specifications ........................................................ 17 Required Breaker Settings (400 V Systems) . . . . . . . . . . . . . . . 20 Appendix ...................................................... ........ 23 TT Systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 IT Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Safety IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS EPO Symbols used in this guide Installation safety Page System Overview UPS Sections Serial number Inverter Section Control/Input/Output Section External Bypass Static Switch Serial number 5Symmetra MW II 1200 kW 3 x 400/230 V Installation - 990-1979E-001 Electrical Installation Typical UPS Wiring Principle Power wiring overview See separate guide on parallel operation for wiring overview in parallel systems. External disconnection switches Input/Output wiring precautions Page Battery cables connection 9Symmetra MW II 1200 kW 3 x 400/230 V Installation - 990-1979E-001 X405 UPS Summary ~~ External Bypass Static Switch Wiring 11Symmetra MW II 1200 kW 3 x 400/230 V Installation - 990-1979E-001 Top cable entry L3 OUT L2 OUT Communication cable overview X184 UVR 31 X181 Relay Boards Relay board 1 connections Relay board 2 connections Page Specifications Low-Impedance/High-Impedance Earthing Electrical Specifications AC Input DC Input AC Output AC Input External Bypass SSW Heat dissipation Notes Torque specifications Required Breaker Settings (400 V Systems) Input and upstream breakers Output and downstream breakers Page Appendix System and Protective Earthing TN Systems Reference to IEC 60364-4-41 413.1.3 Reference to IEC 60364-5-54 546.2.3 Additional requirements for generating sets (IEC 60364-5-55 551.4.2) Protective devices in TN systems TT Systems Reference to IEC 60364-4-41 413.1.4 Protective devices in TT systems IT Systems Reference to IEC 60364-4-41 413.1.5 Protective devices in IT systems Symmetra MW II 1200 kW 3 400/230 V Installation - 990-1979E-00128 Symmetra MW See: IEC 60364-4-41 413.1.3 Switchgear box 29Symmetra MW II 1200 kW 3 400/230 V Installation - 990-1979E-001 Symmetra MW See: IEC 60364-4-41 413.1.4 and "Strkstrmsbekendtgrelsen" 551.6.3, Note ( 551.6.3 is missing in IEC 60364-5-55 ) Strkstrmsbekendtgrelsen 551.6.3 Note Symmetra MW II 1200 kW 3 400/230 V Installation - 990-1979E-00130 Symmetra MW See: IEC 60364-4-41 413.1.3 box breaker 31Symmetra MW II 1200 kW 3 400/230 V Installation - 990-1979E-001 Symmetra MW See: IEC 60364-4-41 413.1.3 This system configuration is not recommended Switchgear Symmetra MW II 1200 kW 3 400/230 V Installation - 990-1979E-00132 Symmetra MW Owing to parallel return path for the fault current used at this point. Residual current protective device can not be 33Symmetra MW II 1200 kW 3 400/230 V Installation - 990-1979E-001 Symmetra MW impedance Grounding Z Page Page 4/2009990-1979E-001 *990-1979E-001* APC Worldwide Customer Support