Batteries, Battery Life | AT&T 9465 instruction

9465 book_1ATT 2/29/00 11:24 PM Page 44

BATTERIES

BATTERIES

Battery Life

Battery life depends on how far the handset is from the base, and other environmental conditions.

NOTE: For optimum battery performance, charge your handset on the base every night.

	Operation:	Approximate Battery Life:

IN USE	Near base unit	4 hours
(phone on)	Away from base unit	2 1/2 hours

NOT IN USE	Powersave off	4 days
	Powersave on	17 days

Charge the Handset Battery Pack

This battery should remain charged up to four days with Powersave turned off and up to 17 days with Powersave on. A fully charged battery provides an average talk time of about three hours.

The battery pack needs charging when:

•A new battery is installed in the handset.

•The phone beeps four times when you press P.

•The battery status symbol on the screen is only partly displayed.

•The phone does not respond when you press P.

Place the handset in the base either in the face-down or face-up position so the CHARGING light turns on. The battery pack is typically fully charged in six hours. For best results, the initial charge should be 12 hours.

You can keep the battery fully charged by returning the handset to the base after each use.

If you repeatedly get a low battery indicator, even after four hours of charging, the battery should be replaced.

44

Image 46

AT&T 9465 manual Batteries, Battery Life, Charge the Handset Battery Pack

Contents

Book1ATT 2/29/00 1123 PM Revised 2/29/00 Part 1 Important Product Information Contents Book1ATT 2/29/00 1123 PM Installation Before You Install Install the handset battery Table/Desk and Wall InstallationAttach belt clip to the cordless handset optional Connect Power cordConnect the telephone line cord Check for dial tone Softkeys Feature SetupMessage Window Display Ringer Off / Battery Save Telephone Feature SetupDial Mode Handset Ringer Caller ID Feature Setup Program Home and Local Area Codes Caller ID with Call Waiting Call List Options Answering System Feature Setup Setup Ring Select / Toll Saver Select Your AnnouncementAudible Message Alert Change Priority Calling Code Change Remote Access CodeReview Feature Settings Record Your Announcement from the Base Delete an Announcement Set the Clock Caller Specific Outgoing Announcement Feature Setup Menu Intcm SPEC-ANN Specific Annc View ADD Review Caller Specific Outgoing Announcements Delete a Caller Specific Outgoing Announcement Telephone Operation Redial Plus RedialTemporary Tone Intercom MuteHold To return to the call, select Unhold Record a Phone Conversation Headset Jack Speaker Volume Base Ringer Volume AT the Base Page/Intercom Handset Locator Talking Caller ID Telephone MEMORY/DIRECTORYPriority Ring Store a Number in Memory from the Handset Memory / Directory Step Replace a Stored Number Store a Pause in a Memory NumberStore a Name with a Memory Number Store a Talking Caller ID Announcement with a Memory Number Dial a Memory Number View Memory Numbers Delete Memory Numbers Edit Memory Numbers Review Talking Caller ID Call History in Telephone Memory About Mailboxes Audible IndicatorsAnswering System Operation Announcement Play/Silent Announcement Bypass Answering CallsCall Screening/Intercept Record a Memo Listen to, Save & Delete Messages CL ↔ AO From the Cordless Handset Call ScreeningConnect with the Answering System From a Touch Tone Phone Remote Access Commands Announcement End remote access callSelect an Outgoing Set the Clock Audible Signals Voice Help Menu Caller ID Operation About Caller Identification Mailbox Link Call WaitingIncoming Call History Memory Match Review Call History Display Dial Delete Call Records from Call History Delete a Specific Call Record Caller ID Display Messages Delete All Call Records Operating Range Charge the Handset Battery Pack Battery LifeBatteries Batteries Replace the Handset Battery Pack If you have no dial tone Case of DifficultyIf the phone does not work at all, check these items first To re-initialize the handset and base If the phone does not ring when you receive a call If you hear noise or interference when using the phoneIf the caller’s name or phone number is not displayed If messages are incomplete If speakerphone conversation sounds distortedIf you have difficulty hearing messages If CL appears in the Message Window If your outgoing announcement isn’t clear Index Index Remote Commands Answering System Remote Command Press