Telnet Configuration Tab with Settings | B&B Electronics MES1A

Getting Started

Figure 13. Telnet Configuration Tab with Settings

Refer to Chapter 4 for configuration details.

Manual Documentation Number: MES1A/MES1B-2106m

PN7138-rev001

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.comB&B Electronics Ltd – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb- europe.com

17

Image 27

B&B Electronics MES1A, MES1B manual Telnet Configuration Tab with Settings

Contents

Models MES1A, MES1B Modbus TCP Modbus Ascii / RTU Converters Manual Documentation Number MES1A/MES1B-2106m International Headquarters Page Manual Documentation Number MES1A/MES1B-2106m PN7138-rev001 Page Table of Contents Configuring the MES1A/B Modbus Basics Manual Documentation Number MES1A/MES1B-2106m Introduction About this ManualSupport About Your MES1A/B Converter Features Hardware Overview Package ChecklistIndicators, Switches and Connectors Power LED Reset Switch Link LEDActivity LED RS-422/485 Connector MES1B only RS-422/485 Switch MES1B onlyEthernet Port Connector DB-9M Serial Port Connector MES1A only RS-485 Two-Wire Mode RS-422/485 Four-Wire Mode Power Connector Connecting the Hardware MES1A Connections MES1B Connections Hardware Overview QuickStart Getting Started Discover the MES1A/B on the Network Using the Device Installer Software Installing the Device InstallerSystem Requirements Discovering Devices Starting the Device Installer Getting Device Details Device Installer Main Window Press Enter to go into Setup Mode Connecting to the MES1A/B Telnet Configuration Tab with Settings Getting Started Telnet Configuration Tab Configuring the MES1A/B Unit ID to IP Address Table Navigating the Configuration Menu To Reconfigure the MES1B, to Factory Settings Saving Configuration SettingsReconfiguring to Factory Settings To Reconfigure the MES1A to Factory Settings IP Address Network/IP Settings Default Gateway Auto-IPStatic IP Address Serial and Mode Settings Telnet Configuration PasswordNetmask Protocol Attached DeviceSerial Protocol Serial Interface MES1A Serial InterfaceMES1B Serial Interface Serial Parameters Modem/Configurable Pin Settings Advanced Modbus Protocol Settings Menu Advanced Modbus Protocol Settings Slave Address / Unit ID Source For Auto…255 = Yes Allow Modbus BroadcastsUse MB/TCP 00BH/00AH Exception Responses = No Disable Modbus/TCP Pipeline Character TimeoutMessage Timeout Close Idle TCP Sockets After Unit ID to IP Address Lookup Table SettingsSerial TX Delay after RX Swap 4x/0H to Get 3x/1x Redundant Entry Retries After Add, Delete, Exit Select FunctionModbus Address From/To Slave IP Address Using Other Device Installer Features Managing Device ListsCreating a New Device List Device List Display Options Display Devices Using IconsSaving Device Lists Opening Device Lists Adding a Device Manually Display the Hardware MAC AddressDisplay the Device Name Using Device Installer to Assign an IP Address Assigning an IP Address using Device Installer Using the Devices Details Tab Adding Info to the Device Details Tab Upgrading Firmware Saving Setup Records Installing Pre-Saved Configuration Files Save Setup Records Dialog Box Installing Setup Records Logging Search and Upgrade Data Options Window, Customization Tab Using Help Using Ping Using Other Device Installer Features Modbus ASCII/RTU Modbus Basics Modbus/TCP Hints and Tips Modbus Basics Swap 4x/0H to get 3x/1x Appendix a Default Configuration Settings Default Configuration Settings Manual CD-ROM disc Appendix B Product Specifications Product Specifications Dimensional Diagram of the MES1A Appendix C Dimensional Diagrams Dimensional Diagram of the MES1B DTE Appendix D Serial Connections MES1B Terminal Block Pin-out for RS-485 Two-Wire Operation Appendix E Network Connections RJ-45 Pin Signal Wire Color Network Connections Declaration of Conformity