Barco R9002790 - page 22

4-3

Connections

R5976336 BARCOSLM R6 Executive 06092001

fixed inputs 1 & 2

5 Cable input or DVI inputs

Variable inputs 3 & 4

2 digital inputs (Optional)

Choice out of :

SDI input order no. : R9840110

HD SDI Digital input order no. : R9840450

Input facilities, RCVDS05 or VS05 connected.

Note : When using a RCVDS05 or VS05, the input configuration of the projector must be as follows:

Slot 1 : RGB/Component

Slot 2 : Video

Slot 3 : not used

Slot 4 : not used

When using a RCVDS05, it is recommended to use a 5-cable output module in the RCVDS. The outputs of this module has to be

connected to slot 1 of the projector.

To switch the projector in the 5-cable mode see chapter 'Installation mode'.

Input Source Connection

Input facilities

Contents

Main Page i Page Page Page Page Page Safety 1 PROJECTORS Warnings To prevent personel injury To prevent projector damage To prevent battery explosion Page Pull To open PACKAGING AND DIMENSIONS Page 3 Ambient Temperature Conditions Humidity Conditions Environment Environment condition check Projector Configurations Which configuration can be used. Positioning the Projector What image size? How big should the image be? Page Page Lenses Which Lens has to be selected. Available lenses Lens formulas to calculate the projector distance Installing the Projection Lens A B Cleaning the lens Battery installation in the RCU. How is the battery delivered ? How to install ? $ CONNECTIONS Lamp Runtime Warning Lamp Light Output Indication Lamp Run Time Indication Switching to Stand-by. Switching Off Page Page Fixed Slot (slot 1 & 2) Which signals can be connected to slot 1 & 2 ? Pin assignment for the DVI connector How to select input Slot 1 or 2 : How to change the input slot setting Note for RCVDS05 users. Page Page Page Page 5 Terminology $ Operating the Projector Switching on Lamp Run Time Indication Lamp Run Time Warning Lamp Light Output Indication Switching to Stand-by. Switching Off Temperature error DMD Quick Set Up Adjustments Quick Language Change Quick Lens Adjustment Using the RCU Pointing to the reflective screen Quick On Screen Color change Page Page How to Program an Address into the RCU ? Controling the Projector Input Selection Picture Contols Display the Projector Address on the Screen Page Start up of the Adjustment Mode 6 Adjustment Mode Possible Paths Password Protection Entering the Password Page 7 Random Access Mode Starting up Overview Flowchart Picture Service Connecting a new Source. Start up the File Service. Possible File Manipulations. File Annotation. Load File Start up the Load File. How to load a file ? The image is not perfect ? Edit File What can be done with the Edit File menu ? How to start up the EDIT menu ? Which items can be adjusted ? How to change the settings ? How to find the correct values for the displayed item? Rename a file Start Up. How to change the characters ? Copy a file How to change the characters ? Delete File Options File Sort File Load Picture Tuning Which Items can be Adjusted ? CTI ON/OFF What is CTI ? How to change the CTI setting ? Color Temperature Available color temperature : Adjusting the Color Temperature. Custom Balance. Gamma What can be adjusted ? How to change the Gamma Value ? Decoding EBU/IRE How can it be selected ? Dynamic Color Depth Purpose : To change the dynamic color depth value : Noise Reduction Purpose : To change the noise reduction value : Input Balance Why adjusting the input balance ? How to adjust the input balance for RGB (Video and S-Video included) input signals ? How to adjust the input balance for YUV input signals? Geometry To start up the Geometry functions : Which geometry adjustments are possible ? How can an adjustment be adjusted ? Shift To start up the shift action : Size To start up the size adjustment : Blanking Available Blanking Adjustment. Adjusting the blanking. Page 8 Installation Mode Input Slots To view or to change the input configuration : Possible results for the fixed input slots 1 & 2 : What if a switcher is connected to the projector ? 800 Peripheral What can be installed ? Defining the Output module of the RCVDS05. Defining the Infrared Communication protocol Convergence How to start up ? How to change this color setting ? Configuration Set up the Correct Configuration OSD color (On-Screen Display) Changing the Background Color Changing the Shutdown Setting No Signal What will happen Changing the Shutdown Time Lens Adjustments Internal Patterns What can be done with these internal patterns ? How to select an internal pattern ? Zoom/Focus/Shift How to Zoom/Focus ? How to shift the image ? Quick Access Keys How to get an overview ? Options Menu Position How to set up? Page 9-1 R5976336 BARCOSLM R6 Executive 06092001 SERVICE MODE Built-up of the service mode. menu 2 menu 3 Identification How to display the Identification screen ? The information Detailed description Change Password How to enable or disable the password function ? About password Types. How to change the password ? Access Control List 9-5 R5976336 BARCOSLM R6 Executive 06092001 Change Projector Address How to change that address ? Change Language Entering the new projector address. Serial Communication Start Up the Serial Communication menu menu 1 menu 2 Setting up the Baud rate Available Baud rates Installing the Interface Standard RS422 Termination Lamp Lamp information light output switching. How to display the lamp menu. Which information is available ? How to switch the constant light output ? BARCO logo Available settings. Add-Ins How to get add ins ? Available Add Ins. How to activate an add-in ? Preset Input Balance Warning How to start up ? Diagnosis. What can be seen ? How to select diagnosis ? 9-10 R5976336 BARCOSLM R6 Executive 06092001 I2C Diagnosis How to select ? Formatter How to select the overview ? Programmable Function Keys 10 Programmable Function Keys What can be done with these keys How can a Function Key be programmed ? Page Appendix A : Standard Source Set Up Files A Appendix A : Standard Source Set Up Files i Symbols A B C M N O P Q