Maintenance Kits
|
| Piece | |
Description |
| Number | |
|
|
| |
Cartridge Bolt Kit |
| 109498 | |
|
| ||
Desiccant Cartridge Service New | 065624 | ||
|
| ||
Desiccant Cartridge Remanufactured | 109493X | ||
|
| ||
Bendix® PuraGuard® Coalescing Cartridge Kit - | 065624PG | ||
Service New |
| ||
|
| ||
PuraGuard Coalescing Cartridge Kit - | 109493PGX | ||
Reman Exchange |
| ||
|
| ||
Delivery Check Valve Kit |
| 109494 | |
|
|
| |
Exhaust Cover Kit |
| 5011327 | |
|
| ||
Extended Purge Kit 3/8" | 5012561N | ||
|
| ||
Extended Purge Kit 3/8" | 5008972N | ||
|
| ||
Extended Purge Kit 1/2" | 5005309N | ||
|
| ||
12 Volt Heater & Thermostat Kit | 109495 | ||
|
| ||
24 Volt Heater & Thermostat Kit | 109496 | ||
Mounting Bracket Kit |
| 5001247 | |
|
|
| |
Silencer Kit |
| K021189 | |
Wiring Harness & Splicing Kit | 109871N | ||
|
|
| |
|
|
| |
Purge Valve Maintenance Kits |
| ||
Purge Valve | Configuration / | Piece | |
Assembly Type | Installation | Number | |
| Bendix® | K022105 | |
|
|
| |
Purge Valve Assembly | Bendix® |
| |
EverFlow® Air Dryer |
| ||
Kit for climate conditions |
| ||
Module | K031560 | ||
above | |||
| |||
|
| ||
| Air Dryer |
| |
Arctic Purge Valve | K031559 | ||
Assembly Kit for climate |
| ||
conditions between |
| ||
Air Dryer Module | K031561 | ||
| |||
| |||
|
| ||
|
|
| |
Purge Valve Assembly | Bendix® |
| |
Kit for climate conditions | K031562 | ||
Discharge Line Unloader | |||
above |
| ||
|
| ||
Arctic Purge Valve |
|
| |
Assembly Kit for climate | K031563 | ||
conditions between | Line Unloader | ||
| |||
to |
|
| |
|
|
| |
HEATER & | |
THERMOSTAT | DRYER END |
CONNECTOR | COVER |
| LOCKING LATCH |
| (MUST BE INSERTED UNTIL IT |
| SNAPS OVER THE MATING CONNECTOR |
| ON |
SIDE VIEW | WEATHERPROOF |
| |
| ACCORDIAN |
TOP VIEW | SEAL |
A two lead wire harness with attached weather resistant connector is available as a service part. One of the two leads is connected to the engine “kill switch” or ignition while the other must be connected to a good vehicle ground. A fuse is installed in the lead carrying vehicle power; install a 10 amp fuse for the 12 volt heater and a 5 amp fuse for the 24 volt heater.
Use 14 AWG wire if it is necessary to lengthen the wire harness leads. Make certain all splices are weatherproofed. Tie wrap or support all electrical wires leading to the
FIGURE 7 - BENDIX® AD-IP® AIR DRYER HEATER AND
THERMOSTAT CONNECTOR
2.Drain all reservoirs to 0 psi. Compressor discharge line may still contain residual pressure.
3.Identify and disconnect the three air lines from the end cover and note the position of end cover ports relative to the vehicle.
4.Unplug the vehicle wiring harness from the heater and thermostat assembly connector on the end cover assembly.
5.Remove the four bolts that secure both the upper and lower mounting brackets to the vehicle, and remove the air dryer from the vehicle.
9
