Setting menu | BenQ CP120 guide

3. Setting menu

	Function	Description
	(default setting/	Description
	value)
	OSD Time (10)	Sets the length of time the OSD will remain active after your last button
		press. The range is from 5 to 100 seconds.
	Quick Cooling	Enables or disables the Quick Cooling function. Selecting On enables
	(On)	the function and projector cooling time will be shortened from a
	(On)	normal 90-second duration to approximately 30 seconds.

		This is a selectable function. Selecting On limits use of the projector to
		only those who know the correct password. When the function is
		activated for the first time, you have to set a password for it. For more
		information, refer to "Utilizing the password function" on page 22.
		Once the password is set and this function is selected, the projector is
		password-protected. Users who do not know the correct password can
		not use the projector.
	Password (off)			WARNING: You will be inconvenienced if you activate the password
	Password (off)
				functionality and subsequently forget the password.
				If viewing online, print out this manual and write the password you
				used in this manual, and keep it in a safe place for later recall.
		The password can be entered by using either the buttons on the
		projector or the remote control.
				The password will display on-screen when being input.
				The password will display on-screen when being input.

	Change	You will be asked to enter the current password before changing to a
	Change	new one. For more information, refer to "Utilizing the password
	Password
	Password	function" on page 22.

Returns all settings to the factory preset values.

Reset	The following settings will still remain: Mirror, Language and

	Password.

Using the projector

41

Image 49

BenQ CP120 manual Setting menu

Contents

Welcome Disclaimer CopyrightSoftware license agreement Copyright Memo Table of Contents Iv Table of Contents Fine-tuning the image size and clarity Table of Contents Dimensions Timing chart Memo Vi Table of Contents But could fail if power cuts or surges Important safety instructionsImportant safety instructions Safety instructions Following environments Do not place this unit on a blanket Do not block the ventilation holesBedding or any other soft surface Other item Safety instructions Introduction Projector featuresIntroduction Shipping contents Front / Upper side Projector exterior viewRear side Lower side External control panel Controls and functionsTurns the projector on or off Introduction Adjusts the focus of the projected image Down on the remote control Remote control descriptionPress this button to display the Wireless Connection menu Turns the projector on or off Installing or replacing the remote control battery Remote control effective range Choosing a location Positioning your projectorObtaining a preferred projected image size Equipment Select your screen size Positioning your projector Maximum Minimum Zoom Screen size chartScreen Center of lens Projection distance Connection Connecting a computerConnection Best video quality Connecting Video source devices Component Video to VGA D-Sub adaptor cable Device Connecting a Component Video source device Video cable Device Connecting an S-Video source device Connecting a composite Video source device Switch all of the connected equipment on Using the projectorUsing the projector Start up To set a password Utilizing the password function To enter the password recall procedure If you forget the passwordTo change the password Auto-adjusting the image Adjusting the heightFine-tuning the image size and clarity That you need using the zoom ring Focus ring Manual keystone correction Correcting keystoneRight buttons on Switching input signal Selecting an application modeHiding the image Automatic keystone correction Remote paging operations Disconnect the power cord from the wall socketFreezing the image Shutdown About wireless connection modes and channels Using the wireless functionsHardware and software requirements Checking the TCP/IP settings of your computer Preparing your computer for wireless connection Installing Wireless Wizard Making wireless presentation Click to select a wireless network card from the list Current wireless connection channel Page Freezing image Controlling presentation Method 2 Projector control Disconnecting Menu system Menu operation Using the menus Picture menu Keystone Selected Application ModeColor Temp Depends on Pro-Picture menu Setting menu Advance menu Auto Off Off Turned off. Selecting Off disables this functionEconomic Periods of time 10hours without shutdown Mode Equivalent ResolutionInformation Menu Source Care of the projector Maintenance Message Status Calculation of lamp hour Replacing the lamp Resetting the lamp counter Temperature information Projector needs to cool after the power is Turned off IndicatorsStand-by mode Powering up Maintenance Projector does not turn on TroubleshootingNo picture Image is unstable Unable to use wireless connection Remote control does not workConfigured Nearby Projector specifications Specifications Timing chart DimensionsHorizontal Vertical Pixel Resolution Frequency Mode KHz MHz Supported timing for PC input Supported timing for Component-YPbPrInput Signal Format Horizontal Frequency Vertical Frequency KHzSupported timing for Video and S-Video inputs Limited warranty WarrantyWarranty FCC statement Regulation statementsEEC statement MIC statement Memo Regulation statements