Connecting component-video devices | BenQ W1500 instruction

Connecting component-video devices

Be sure to match the corresponding colors between the cables and the terminals. The RCA type component video jacks are provided for connection to video output devices. You should also connect the separate audio cable to a suitable audio amplifier.

AV equipment: DVD player, digital

tuner, etc.

From audio output	To audio input
terminals	terminals

Component video cable

Connecting S-Video or video devices

You need to connect only S-Video or composite Video cable from the same device, never both at the same time. You should also connect the separate audio cable to a suitable audio amplifier.

AV equipment	From audio output To audio input terminals
	terminals

S-Video cable

or

Video cable

• If you have already made a Component Video connection between the projector and the video source device, you need not connect to this device again using an S-Video or composite Video connection as this makes an unnecessary second connection of poorer picture quality. You need only connect using a composite Video connection if both Component Video and S-Video are not supplied on the video source device (for example, with some analog video cameras).

•If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, please check that the video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

Important safety instructions

21

Image 21

BenQ W1500 user manual Connecting component-video devices, Connecting S-Video or video devices

Contents

W1500 Digital Projector Home Cinema Series Table of contents Important safety instructions Important safety instructions Moisture condensation Avoid volatile liquidsDisposal Overview Shipping contents Replacing the remote control batteries Remote control effective rangeCeiling mounting the projector Important safety instructions Projector features Front and upper side view Rear and lower side view Projector exterior viewRS-232 control port Audio L/R input jacks Control panel Controls and functions Remote control Front Choosing a locationFront Ceiling Rear Determine the aspect ratio of your screen, 169 or 43? Obtaining a preferred projected image size Important safety instructions Installation for a 169 ratio screen Projection dimensions Floor Installation Ceiling Installation Installation for a 43 ratio screenScreen aspect ratio is 43 and the projected picture is Lowest Highest To use the lens shift lever Shifting the projection lens vertically Terminal appearance Reference PreparationsName Component Connecting Hdmi devices Connecting S-Video or video devices Connecting component-video devices Connect the projector to a computer with a VGA cable Connecting a computer Preparations Turning the projector on Sharpen the picture by rotating the focus ring Selecting an input source Using a security cable lock Using the menusUse / to highlight the System Setup menu Securing the projector Setting a password Utilizing the password functionIf you forget the password As the picture indicates, the four arrow keys Changing the password Entering the password recall procedureDisabling the password function Write down the number and turn off your projector Adjusting the projected image Adjusting the projection angleCorrecting picture distortion Selecting a preset mode Using the preset and user modesFine-tuning the selected picture mode Setting the User 1/User 2/User 3 mode Resetting the picture mode Fine-tuning the picture qualityAdjusting Brightness Adjusting Contrast Adjusting Tint Adjusting ColorAdjusting Sharpness Adjusting Flesh Tone Setting a preferred color temperature Setting Black LevelTo set a preferred color temperature Advanced picture quality controls Selecting a Gamma setting Adjusting Brilliant ColorColor Management Setting Film Mode Setting 3D Comb FilterTo leave and save the settings, press MENU/EXIT Adjusting the sound level Adjusting the soundSwitching the left/right audio channels Turning off the Power On/Off Ring Tone About the aspect ratio Selecting the aspect ratio Using the test pattern Freezing the imageMagnifying and searching for details Operating in a high altitude environment To activate High Altitude Mode To display the PIP window Using the remote control Using the OSD menuDisplaying more than one image source simultaneously Watching 3D content Connecting 3D video devicesUsing the 3D menus Personalizing the projector menu display Locking control keysTo lock the keys Turning the projector off On-Screen Display OSD menus Audio SetupOn-Screen Display OSD structure Main menu Sub-menu Options Display System Setup Auto Off Setup AdvancedInformation Function Description Picture -- Basic menu Audio Setup menu Display menu Advanced Setup menu System Setup menu Password High Altitude ModeReset All Settings Test Pattern Information menu Cleaning the projector case Cleaning the lensCare of the projector Storing the projector Lamp information Getting to know the lamp hourExtending lamp life Timing of replacing the lamp Replacing the lampStatus Do not turn on the power with lamp cover removed Use the handle to slowly pull lamp housing out Projector Connect the power and restart the projector Resetting the lamp timer Indicators Power Temp Lamp Status & DescriptionLamp Status & Description Problem Cause Remedy TroubleshootingYour Blu-ray Disc is not in 3D Format Specifications Ceiling mount installation Dimensions Timing chart Resolution Mode Refresh rate Freq. KHz Clock MHzSupported timing for PC input 1920 x 59.939/60 67.432/67.5 148.35/148.5 Supported timing for Hdmi Hdcp input 1400 x SXGA+60 59.978 65.317 121.750 Timing Resolution Freq. Hz Freq. KHz Dot Clock Freq. MHz Resolution Mode Refresh rate Hz Freq. KHz Clock MHz Video Mode Freq. KHz Freq. Hz Sub-carrier Frequency MHzSupported timing for Video and S-Video inputs Copyright WarrantyDisclaimer Patents