Remove the lamp cover | BenQ W6500 instruction

English

1.Turn the power off and disconnect the projector from the power outlet. Turn off all connected equipment and disconnect all other cables. See "Turning the projector off" on page 36 for details.

2.Slightly lift the projector up. Loosen the screws on the lamp cover (located on the left side).

3.Remove the lamp cover.

4.Loosen the screws that hold the lamp to the projector. If the screws are not loosened completely, they could injure your fingers.

5.Lift the handle so that it is perpendicular to the lamp. Use the handle to slowly pull the lamp out of the projector.

Notes

•Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector. To reduce the risk of injuries to fingers and damage to internal components, use caution when removing lamp glass that has shattered.

•Do not place the lamp in locations where water might splash on it, children can reach it, near or above heat sources, or near flammable materials.

•Do not insert your hand into the projector when the lamp is removed. If you touch the optical components inside, it could cause blurred images.

6.Insert the replacement lamp. Make sure it is pushed fully and firmly in place.

7.Tighten the screws securing the lamp box.

8.Ensure the handle is fully locked in place.

Notes

•Please be careful to not over-tighten the screws.

•Loose screws may cause a bad connection, which could result in malfunction.

9.Re-install the lamp cover.

10.Tighten the screws on the lamp cover.

11.Reapply power and turn the projector back on.

46 Additional information

Image 46

BenQ W6500 user manual Remove the lamp cover

Contents

Welcome W6000/W6500 Digital Projector Home Cinema Series Table of contents Important safety instructions Do not cover the projector with any item Avoid volatile liquids Moisture condensationDisposal Shipping contents Overview Remote control operation Remote control batteriesCeiling mounting the projector Projector features Rear view Projector exterior viewFront and upper side view Under view Control panel Test Remote controlPicture window control keys PIP, Size Info Ceiling Front Choosing a locationFloor Front Floor Rear Obtaining a preferred projected image size Determine the aspect ratio of your screen, 169 or 43? Projection dimensions Installation for a 169 ratio screen Lens Installation for a 43 ratio screenHighest Height H Shifting the projection lens To use the lens shift lever Reference Picture quality Connecting Hdmi devicesPreparations Component Connecting component-video devices Connecting S-Video or video devices Connecting a computer Connect the projector to a computer with a VGA cable Turning the projector on Preparations Adjust the projected picture to the size that Fine-tuning the image size and clarityUsing the OSD menu You need using the zoom ring Ring Use / to highlight the System Setup menu Using the menusUsing a security cable lock Securing the projector If you forget the password Utilizing the password functionSetting a password To leave the OSD menu, press Menu Disabling the password function Entering the password recall procedureChanging the password Write down the number and turn off your projector Correcting picture distortion Adjusting the projected imageAdjusting the projection angle Two parallel sides Fine-tuning the selected picture mode Using the preset and user modesSelecting a preset mode To fine-tune the picture mode Press to highlight Load Settings From Setting the User 1/User 2/User 3 modeResetting the picture mode To reset the picture mode to the preset factory values Fine-tuning the picture quality Advanced picture quality controls Setting Black LevelSelecting a color temperature Controlling image clarity Adjusting Brilliant Color Setting a preferred color temperatureSelecting a Gamma setting To set a preferred color temperature To adjust and store the settings Setting Film ModeColor Management Selecting the aspect ratio Setting 3D Comb FilterAbout the aspect ratio Aspect ratio Aspect ratio image Using Panamorph lenses optionalImage Using the entire resolution 169 display To activate High Altitude Mode Operating in a high altitude environment Highlight PIP and press / to select On To display the PIP window Using the remote controlDisplaying more than one image source simultaneously PIP function is effective at below source combinations Turning the projector off Personalizing the projector menu displayLocking control keys To lock the keys On-Screen Display OSD structure On-Screen Display OSD menusMain menu Sub-menu Options Setup System SetupInformation Resolution Picture -- Advanced menu Picture -- Basic menuFunction Description System Setup menu Display menu Lamp Power Normal Menu SettingsAdvanced Setup menu Reset Lamp Timer Information menu Care of the projector Cleaning the lensCleaning the projector case Storing the projector Lamp information Setting Lamp Power as EconomicSetting Auto Off Getting to know the lamp hour Replacing the lamp Timing of replacing the lampStatus Message Remove the lamp cover Resetting the lamp timer Power IndicatorsPower Temp Lamp Status & Description Lamp Status & Description Troubleshooting Problem Cause Remedy Electrical SpecificationsOptical Terminals Ceiling mount installation DimensionsMm x 317 mm x 145 mm W x D x H Supported timing for PC input Timing chartFormat Resolution Refresh rate Frequency KHz MHz Supported timing for Edtv and Hdtv via Component inputs Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Supported timing for Video and S-Video inputs Copyright WarrantyDisclaimer MIC statement FCC statement for United States usersEEC statement for European users Weee directive English