Bosch Appliances DVA-08K instruction

Image 21

Bosch Appliances DVA-08K manual

Contents

DVA-08K SCSI Premium Series RAID Subsystem DVA-08KPage RAID Subsystem DVA-08K Installation Manual Table of ContentsTable of Contents en Bosch Security Systems Subsystem Connection and Operation Precautions and Instructions Safety PrecautionsESD Precautions Warnings and Certifications Reorient or relocate the receiving antenna Introduction Product OverviewSCSI Host Ports Active Components Enclosure Chassis Physical Dimensions2.2.1 Chassis Overview 2.2.5Rear Panel Overview 2.2.4Hard Drive Numbering 2.2.6Backplane Board Subsystem Components 2.3.1LCD Panel 2.3.3 2.3.2Drive TraysThe RAID Controller Module Controller Module Interfaces DIMM Module 2.3.4Battery Backup Unit 2.3.5 Power Supply Units2.3.6 Cooling Fan Modules Intelligent Dual Speed Operation Advanced Fault-Preventative Operation Audible Alarms LED IndicatorsSubsystem Monitoring 2.4.1 2.5.1 Hot-Swappable ComponentsHot-Swap Capabilities 2.5.2 Installation Prerequisites Hardware Installation Static-Free Installation Precautions and InstructionsBBU Warnings and Precautions 3.2.1 Install or replace the BBU module only with a BBU module supplied by your subsystem vendor. Use of battery cells provided by another source will void our warranty Installation Procedure Flowchart General Installation ProcedureSection 5.4 Power On Installation Procedure 3.5Rackmounting Considerations for Installation Site and Chassis3.5.1 3.5.2 3.6Drive Tray Installation 6. Once all drive trays are installed, the RAID subsystem will poll the drive channels and rec- ognize the drives and scan them in automatically Subsystem Monitoring Overview Subsystem Monitoring 4.2.1 Status-indicating LEDsBrief Overview of the LEDs Component 4.2.2Drive Tray LEDs Power Status4.2.3 Controller Module LEDs Ethernet Port LEDs 4.2.4Name Link Status 4.2.6 4.2.5BBU Module LEDPSU LED 4.2.7LCD Keypad Panel POWER 4.2.8Cooling Fan Module LEDBUSY Default Threshold Values Audible Alarm4.3.1 Upper Threshold 4.4I2C Monitoring 4.3.2Failed Devices Subsystem Connection and Operation Basic Configuration Rules 5.2.1 SCSI Connection OverviewSCSI Cables 5.2.2 SCSI Termination 5.2.3 Host Connection Topology Default Channel SettingsModel Host Channels Power On Checklist Power OnPower On Sequence Power On Procedure Power On Status Check 5.4.45.4.5LCD Screen 40 en Subsystem Connection and Operation Power Off Procedure General Notes on Component Replacement Subsystem Maintenance3. BBU module - Section 6.4 Replacing a Faulty BBU Overview Replacing Controller Module Components Notes on Controller Module Maintenance6.2.1Overview 6.2.2 Replacing the Controller Module 6.2.4 DIMM Module Installation Memory Module Installation OverviewReplacing or Upgrading Memory Modules 6.3.1 3. Gently retrieve the DIMM module out of the DIMM socket. See Figure Notes on PSU Module Maintenance Replacing a Faulty BBUReplacing a Failed PSU Module 6.5.1 The screw is located below the extraction lever, beside the LED indicator, and can be hid- den from sight 7. Insert the new PSU module into the subsystem Once the previously removed cooling module has been installed, insert the new PSU module into the subsystem. Make sure the extraction lever is in its downright position so that the saddle notches on the lower edges of the handle can lock on to the edge metal brackets along the chassis inner walls. Push the PSU into the slot and pull the handle upwards to secure the module Replacing a Failed Cooling Fan Module Notes on Cooling Fan Module Maintenance6.6.1 6.6.2Replacing a Cooling Fan Module Notes on Hard Drive Maintenance Drive Tray Maintenance6.7.1 6.7.2Replacing a Failed Hard Drive Drive type The subsystem can use either SATA-II or SATA-I hard drives Fig. 6.10 Installing a SATA Hard Drive Environmental Specifications Appendix Technical SpecificationsPower Requirements Dimensions Warning Alarms Safety RequirementsShock Vibration Configuration Controller SpecificationsSpecifications 7.1.1 Power Supply Specifications Drive Tray Specifications RAID Management Cooling Module Specifications Fault Tolerance Management Spare Parts List Appendix Spare Parts and AccessoriesSpare Parts 8.1.1 Accessories and Optional Items Appendix Pinouts SCSI Port VHDCI Connector Pinouts CN1 Pin Number COM1 Cable DB9 and Audio Jack PinoutsPin Name CN2 Pin Number Main Power Null ModemEthernet Port Pinouts 10 Index terminal emulation program 17 terminal management 14 threshold values warning alarmsunder charge ventilation clearancePage Robert-Koch-Straße D-85521 Ottobrunn Bosch Security SystemsGermany Telefon