Appendix Pinouts, Name | Bosch Appliances DVA-08K specification

Image 62

Bosch Appliances DVA-08K manual Appendix Pinouts, SCSI Port VHDCI Connector Pinouts, Name

Contents

RAID Subsystem DVA-08K DVA-08K SCSI Premium SeriesPage Table of Contents en Table of ContentsRAID Subsystem DVA-08K Installation Manual Bosch Security Systems Subsystem Connection and Operation ESD Precautions Safety PrecautionsPrecautions and Instructions Warnings and Certifications Reorient or relocate the receiving antenna SCSI Host Ports IntroductionProduct Overview Active Components 2.2.1 Physical DimensionsEnclosure Chassis Chassis Overview 2.2.4Hard Drive Numbering 2.2.5Rear Panel Overview 2.2.6Backplane Board LCD Panel Subsystem Components2.3.1 The RAID Controller Module 2.3.2Drive Trays2.3.3 Controller Module Interfaces 2.3.4Battery Backup Unit DIMM Module 2.3.6 Power Supply Units2.3.5 Cooling Fan Modules Advanced Fault-Preventative Operation Intelligent Dual Speed Operation Subsystem Monitoring LED IndicatorsAudible Alarms 2.4.1 Hot-Swap Capabilities Hot-Swappable Components2.5.1 2.5.2 Hardware Installation Installation Prerequisites BBU Warnings and Precautions Precautions and InstructionsStatic-Free Installation 3.2.1 Install or replace the BBU module only with a BBU module supplied by your subsystem vendor. Use of battery cells provided by another source will void our warranty Section 5.4 Power On General Installation ProcedureInstallation Procedure Flowchart Installation Procedure 3.5.1 Considerations for Installation Site and Chassis3.5Rackmounting 3.5.2 3.6Drive Tray Installation 6. Once all drive trays are installed, the RAID subsystem will poll the drive channels and rec- ognize the drives and scan them in automatically Subsystem Monitoring Subsystem Monitoring Overview Brief Overview of the LEDs Status-indicating LEDs4.2.1 Component 4.2.3 Power Status4.2.2Drive Tray LEDs Controller Module LEDs Name 4.2.4Ethernet Port LEDs Link Status PSU LED 4.2.5BBU Module LED4.2.6 4.2.7LCD Keypad Panel BUSY POWER4.2.8Cooling Fan Module LED 4.3.1 Audible AlarmDefault Threshold Values Upper Threshold Failed Devices 4.4I2C Monitoring4.3.2 Basic Configuration Rules Subsystem Connection and Operation SCSI Cables SCSI Connection Overview5.2.1 5.2.2 5.2.3 SCSI Termination Model Default Channel SettingsHost Connection Topology Host Channels Power On Sequence Power OnPower On Checklist Power On Procedure 5.4.5LCD Screen Power On Status Check5.4.4 40 en Subsystem Connection and Operation Power Off Procedure 3. BBU module - Section 6.4 Replacing a Faulty BBU Subsystem MaintenanceGeneral Notes on Component Replacement Overview 6.2.1Overview Notes on Controller Module MaintenanceReplacing Controller Module Components 6.2.2 6.2.4 Replacing the Controller Module Replacing or Upgrading Memory Modules Memory Module Installation OverviewDIMM Module Installation 6.3.1 3. Gently retrieve the DIMM module out of the DIMM socket. See Figure Replacing a Failed PSU Module Replacing a Faulty BBUNotes on PSU Module Maintenance 6.5.1 The screw is located below the extraction lever, beside the LED indicator, and can be hid- den from sight 7. Insert the new PSU module into the subsystem Once the previously removed cooling module has been installed, insert the new PSU module into the subsystem. Make sure the extraction lever is in its downright position so that the saddle notches on the lower edges of the handle can lock on to the edge metal brackets along the chassis inner walls. Push the PSU into the slot and pull the handle upwards to secure the module 6.6.1 Notes on Cooling Fan Module MaintenanceReplacing a Failed Cooling Fan Module 6.6.2Replacing a Cooling Fan Module 6.7.1 Drive Tray MaintenanceNotes on Hard Drive Maintenance 6.7.2Replacing a Failed Hard Drive Drive type The subsystem can use either SATA-II or SATA-I hard drives Fig. 6.10 Installing a SATA Hard Drive Power Requirements Appendix Technical SpecificationsEnvironmental Specifications Dimensions Shock Safety RequirementsWarning Alarms Vibration Specifications Controller SpecificationsConfiguration 7.1.1 Drive Tray Specifications Power Supply Specifications Cooling Module Specifications RAID Management Fault Tolerance Management Spare Parts Appendix Spare Parts and AccessoriesSpare Parts List 8.1.1 Accessories and Optional Items SCSI Port VHDCI Connector Pinouts Appendix Pinouts Pin Name COM1 Cable DB9 and Audio Jack PinoutsCN1 Pin Number CN2 Pin Number Ethernet Port Pinouts Main PowerNull Modem 10 Index under charge warning alarmsterminal emulation program 17 terminal management 14 threshold values ventilation clearancePage Germany Bosch Security SystemsRobert-Koch-Straße D-85521 Ottobrunn Telefon