3.5Rackmounting, 3.5.1, 3.5.2 | Bosch Appliances DVA-08K specs

Image 23

Bosch Appliances DVA-08K manual 3.5Rackmounting, 3.5.1, Considerations for Installation Site and Chassis, 3.5.2

Contents

DVA-08K SCSI Premium Series RAID Subsystem DVA-08KPage Bosch Security Systems Table of ContentsRAID Subsystem DVA-08K Installation Manual Table of Contents en Subsystem Connection and Operation Warnings and Certifications Safety PrecautionsPrecautions and Instructions ESD Precautions Reorient or relocate the receiving antenna SCSI Host Ports IntroductionProduct Overview Active Components Chassis Overview Physical DimensionsEnclosure Chassis 2.2.1 2.2.5Rear Panel Overview 2.2.4Hard Drive Numbering 2.2.6Backplane Board LCD Panel Subsystem Components2.3.1 Controller Module Interfaces 2.3.2Drive Trays2.3.3 The RAID Controller Module DIMM Module 2.3.4Battery Backup Unit Cooling Fan Modules Power Supply Units2.3.5 2.3.6 Intelligent Dual Speed Operation Advanced Fault-Preventative Operation 2.4.1 LED IndicatorsAudible Alarms Subsystem Monitoring 2.5.2 Hot-Swappable Components2.5.1 Hot-Swap Capabilities Installation Prerequisites Hardware Installation 3.2.1 Precautions and InstructionsStatic-Free Installation BBU Warnings and Precautions Install or replace the BBU module only with a BBU module supplied by your subsystem vendor. Use of battery cells provided by another source will void our warranty Installation Procedure General Installation ProcedureInstallation Procedure Flowchart Section 5.4 Power On 3.5.2 Considerations for Installation Site and Chassis3.5Rackmounting 3.5.1 3.6Drive Tray Installation 6. Once all drive trays are installed, the RAID subsystem will poll the drive channels and rec- ognize the drives and scan them in automatically Subsystem Monitoring Overview Subsystem Monitoring Component Status-indicating LEDs4.2.1 Brief Overview of the LEDs Controller Module LEDs Power Status4.2.2Drive Tray LEDs 4.2.3 Link Status 4.2.4Ethernet Port LEDs Name 4.2.7LCD Keypad Panel 4.2.5BBU Module LED4.2.6 PSU LED BUSY POWER4.2.8Cooling Fan Module LED Upper Threshold Audible AlarmDefault Threshold Values 4.3.1 Failed Devices 4.4I2C Monitoring4.3.2 Subsystem Connection and Operation Basic Configuration Rules 5.2.2 SCSI Connection Overview5.2.1 SCSI Cables SCSI Termination 5.2.3 Host Channels Default Channel SettingsHost Connection Topology Model Power On Procedure Power OnPower On Checklist Power On Sequence 5.4.5LCD Screen Power On Status Check5.4.4 40 en Subsystem Connection and Operation Power Off Procedure Overview Subsystem MaintenanceGeneral Notes on Component Replacement 3. BBU module - Section 6.4 Replacing a Faulty BBU 6.2.2 Notes on Controller Module MaintenanceReplacing Controller Module Components 6.2.1Overview Replacing the Controller Module 6.2.4 6.3.1 Memory Module Installation OverviewDIMM Module Installation Replacing or Upgrading Memory Modules 3. Gently retrieve the DIMM module out of the DIMM socket. See Figure 6.5.1 Replacing a Faulty BBUNotes on PSU Module Maintenance Replacing a Failed PSU Module The screw is located below the extraction lever, beside the LED indicator, and can be hid- den from sight 7. Insert the new PSU module into the subsystem Once the previously removed cooling module has been installed, insert the new PSU module into the subsystem. Make sure the extraction lever is in its downright position so that the saddle notches on the lower edges of the handle can lock on to the edge metal brackets along the chassis inner walls. Push the PSU into the slot and pull the handle upwards to secure the module 6.6.2Replacing a Cooling Fan Module Notes on Cooling Fan Module MaintenanceReplacing a Failed Cooling Fan Module 6.6.1 6.7.2Replacing a Failed Hard Drive Drive Tray MaintenanceNotes on Hard Drive Maintenance 6.7.1 Drive type The subsystem can use either SATA-II or SATA-I hard drives Fig. 6.10 Installing a SATA Hard Drive Dimensions Appendix Technical SpecificationsEnvironmental Specifications Power Requirements Vibration Safety RequirementsWarning Alarms Shock 7.1.1 Controller SpecificationsConfiguration Specifications Power Supply Specifications Drive Tray Specifications RAID Management Cooling Module Specifications Fault Tolerance Management 8.1.1 Appendix Spare Parts and AccessoriesSpare Parts List Spare Parts Accessories and Optional Items Appendix Pinouts SCSI Port VHDCI Connector Pinouts CN2 Pin Number COM1 Cable DB9 and Audio Jack PinoutsCN1 Pin Number Pin Name Ethernet Port Pinouts Main PowerNull Modem 10 Index ventilation clearance warning alarmsterminal emulation program 17 terminal management 14 threshold values under chargePage Telefon Bosch Security SystemsRobert-Koch-Straße D-85521 Ottobrunn Germany