Bosch Appliances DVA-08K specs

Image 48

Bosch Appliances DVA-08K manual

Contents

RAID Subsystem DVA-08K DVA-08K SCSI Premium SeriesPage Table of Contents RAID Subsystem DVA-08K Installation ManualTable of Contents en Bosch Security Systems Subsystem Connection and Operation Safety Precautions Precautions and InstructionsESD Precautions Warnings and Certifications Reorient or relocate the receiving antenna Introduction Product OverviewSCSI Host Ports Active Components Physical Dimensions Enclosure Chassis2.2.1 Chassis Overview 2.2.4Hard Drive Numbering 2.2.5Rear Panel Overview 2.2.6Backplane Board Subsystem Components 2.3.1LCD Panel 2.3.2Drive Trays 2.3.3The RAID Controller Module Controller Module Interfaces 2.3.4Battery Backup Unit DIMM Module Power Supply Units 2.3.52.3.6 Cooling Fan Modules Advanced Fault-Preventative Operation Intelligent Dual Speed Operation LED Indicators Audible AlarmsSubsystem Monitoring 2.4.1 Hot-Swappable Components 2.5.1Hot-Swap Capabilities 2.5.2 Hardware Installation Installation Prerequisites Precautions and Instructions Static-Free InstallationBBU Warnings and Precautions 3.2.1 Install or replace the BBU module only with a BBU module supplied by your subsystem vendor. Use of battery cells provided by another source will void our warranty General Installation Procedure Installation Procedure FlowchartSection 5.4 Power On Installation Procedure Considerations for Installation Site and Chassis 3.5Rackmounting3.5.1 3.5.2 3.6Drive Tray Installation 6. Once all drive trays are installed, the RAID subsystem will poll the drive channels and rec- ognize the drives and scan them in automatically Subsystem Monitoring Subsystem Monitoring Overview Status-indicating LEDs 4.2.1Brief Overview of the LEDs Component Power Status 4.2.2Drive Tray LEDs4.2.3 Controller Module LEDs 4.2.4 Ethernet Port LEDsName Link Status 4.2.5BBU Module LED 4.2.6PSU LED 4.2.7LCD Keypad Panel POWER 4.2.8Cooling Fan Module LEDBUSY Audible Alarm Default Threshold Values4.3.1 Upper Threshold 4.4I2C Monitoring 4.3.2Failed Devices Basic Configuration Rules Subsystem Connection and Operation SCSI Connection Overview 5.2.1SCSI Cables 5.2.2 5.2.3 SCSI Termination Default Channel Settings Host Connection TopologyModel Host Channels Power On Power On ChecklistPower On Sequence Power On Procedure Power On Status Check 5.4.45.4.5LCD Screen 40 en Subsystem Connection and Operation Power Off Procedure Subsystem Maintenance General Notes on Component Replacement3. BBU module - Section 6.4 Replacing a Faulty BBU Overview Notes on Controller Module Maintenance Replacing Controller Module Components6.2.1Overview 6.2.2 6.2.4 Replacing the Controller Module Memory Module Installation Overview DIMM Module InstallationReplacing or Upgrading Memory Modules 6.3.1 3. Gently retrieve the DIMM module out of the DIMM socket. See Figure Replacing a Faulty BBU Notes on PSU Module MaintenanceReplacing a Failed PSU Module 6.5.1 The screw is located below the extraction lever, beside the LED indicator, and can be hid- den from sight 7. Insert the new PSU module into the subsystem Once the previously removed cooling module has been installed, insert the new PSU module into the subsystem. Make sure the extraction lever is in its downright position so that the saddle notches on the lower edges of the handle can lock on to the edge metal brackets along the chassis inner walls. Push the PSU into the slot and pull the handle upwards to secure the module Notes on Cooling Fan Module Maintenance Replacing a Failed Cooling Fan Module6.6.1 6.6.2Replacing a Cooling Fan Module Drive Tray Maintenance Notes on Hard Drive Maintenance6.7.1 6.7.2Replacing a Failed Hard Drive Drive type The subsystem can use either SATA-II or SATA-I hard drives Fig. 6.10 Installing a SATA Hard Drive Appendix Technical Specifications Environmental SpecificationsPower Requirements Dimensions Safety Requirements Warning AlarmsShock Vibration Controller Specifications ConfigurationSpecifications 7.1.1 Drive Tray Specifications Power Supply Specifications Cooling Module Specifications RAID Management Fault Tolerance Management Appendix Spare Parts and Accessories Spare Parts ListSpare Parts 8.1.1 Accessories and Optional Items SCSI Port VHDCI Connector Pinouts Appendix Pinouts COM1 Cable DB9 and Audio Jack Pinouts CN1 Pin NumberPin Name CN2 Pin Number Main Power Null ModemEthernet Port Pinouts 10 Index warning alarms terminal emulation program 17 terminal management 14 threshold valuesunder charge ventilation clearancePage Bosch Security Systems Robert-Koch-Straße D-85521 OttobrunnGermany Telefon