BM 2610007877
Troubleshooting
Troubleshooting Guide - General
|
|
|
|
|
|
|
| pROBlEM |
| CAUSE |
| CORRECTIVE ACTION |
|
|
|
|
|
|
| |
| Head assembly does not bevel | 1. | Bevel detent pin is engaged. | - Pull out 33.9° bevel detent pin, then |
| |
| to desired position. |
| and locks bevel angle at 33.9°. |
| rotate pin 1/4 turn to keep out. |
|
|
| 2. | Bevel range selector knob | - | Change bevel range selector |
|
|
|
| setting limits movement. |
| knob position (see page 41). |
|
|
|
|
|
|
| |
| Blade hits table. | Misalignment. | - | Authorized service. |
| |
|
|
|
|
|
| |
| Angle of cut not accurate. | Angle stops at 0° or 45° need | - | See Adjustments section |
| |
|
| adjustment. |
| (pages |
| |
|
|
|
|
|
|
|
| Cannot rotate table to change miter | 1. | Miter lock knob is tightened. | - | Turn miter lock knob |
|
| angle. |
|
|
| counterclockwise to loosen. |
|
|
| 2. | Miter detent lever is engaged with | - | Pull up on miter detent lever to |
|
|
|
| a detent (slot) in detent plate. |
| disengage from detent slot (see |
|
|
|
|
|
| page 33). |
|
|
| 3. Sawdust accumulation. | - | Vacuum or blow out dust around |
| |
|
|
|
|
| turntable; wear eye protection. |
|
|
|
|
|
|
|
|
| Head assembly will not fully raise | 1. | Head assembly lock pin is | - | Pull out lock pin, allowing head |
|
| or blade guard will not fully close. |
| engaged. |
| assembly to go up (see |
|
|
|
|
|
| page 17). |
|
|
| 2. | Cover plate not tightened after | - | See Removing and Installing |
|
|
|
| replacing blade. |
| Blades on pages |
|
|
| 3. Sawdust accumulation. | - | Clean head assembly. |
| |
|
| 4. | Sawdust accumulation. | - | Authorized service. |
|
|
|
|
|
|
| |
| Blade binds, jams, burns wood. | 1. Improper operation. | - | See Saw Operations |
| |
| Rough cuts. |
|
|
| section. |
|
|
| 2. | Dull blade. | - | Replace or sharpen blade. |
|
|
| 3. | Improper blade. | - | Replace with 12" diameter blade |
|
|
|
|
|
| designed for material being cut. |
|
|
| 4. | Bent blade. | - | Replace blade. |
|
|
|
|
|
| ||
| Head assembly slides forward and | Mechanism lock lever is | Pull up on mechanism lock lever |
| ||
| back when making a chop cut. | disengaged. | tab to engage (see page 18). |
| ||
|
|
|
|
| ||
| Bevel angle is not securely held | Bevel lock lever needs tension | Increase bevel lock lever force by |
| ||
| when bevel lock lever is pushed. | adjustment. | adjusting tension nut (see page 25). |
| ||
|
|
|
|
| ||
| Glide mechanism is difficult to | Glide movement controller is set | Loosen two screws on the |
| ||
| move forward and back. | too tight. | movement controller (see page 17). |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
54.
