Attach the Faceplate Back Panels | Bowflex 001-6961 guide

	Assembly Guide
	Step 20 - Attach the Faceplate Back Panels	Figure 20
		Figure 20
	Locate the following items:	28
		28
	• Item #27 - Faceplate Right Back Panels	27
	• Item #28 - Faceplate Left Back Panels	27
	• Item #28 - Faceplate Left Back Panels	A
	• From Step 19 - Main Assembly	A
	• From Step 19 - Main Assembly
	• Item #A - (2) #10 Phillips Head Screws
	Slide each Faceplate Back Panel (Items #27 & 28), textured
	side out, against the textured (back) side of the Faceplate.
	The screw heads of the (2) Phillips Head Screws installed
	during Step 19 should allow the Back Panels to slide beneath
	them until the panels meet in the center..
	Secure the Panels using (2) #10 Phillips Head Screws (Item
	#A), as shown in Figure 20, attaching one side at a time.
	Completely tighten hardware installed during Steps 19 & 20.
		Main
		Assembly
	Step 21 - Tighten Lower Bolt on the Seat Bracket	Figure 21
	Locate the following items:

•From Step 5 - Seat Assembly (underneath)

Using an Allen Wrench (included) and a combination wrench, tighten the top nut & bolt on the Seat Assembly (see Figure 21). Take care that the Seat Assembly can still freely slide without resistance along the Seat Rail when you are seated.

Note: The Seat Assembly will have some resistance when rolling if no one is seated.

Take care not to overtighten hardware from Step 21.

Nut

17

Image 19

Bowflex 001-6961 manual Attach the Faceplate Back Panels, Tighten Lower Bolt on the Seat Bracket

Contents

Bowflex Sport Home Gym Assembly Instructions Table of Contents Safety Precautions Home Gym Get to Know Your Machine Basic Assembly Principles Tools You Will Need Hardware Guide Attach the Lower Lat Tower to the Base Platform Assembly GuideAttach the Base Legs to the Base Platform Completely tighten hardware installed during Step Attach the Squat Platform to the Main Assembly Insert the screws through the lined up holes in the Chest Attach the Chest Bar with Pulleys to Main AssemblyAttach the Seat Bracket to the Seat Pad Button Head Screws Item #K one washer per screw Attach the Rear Leg to the Rear Leg Cross Tube Attach the Seat Rail to the Seat Assembly Do not over-tighten hardware from Step Assembly can move freelyAttach the Rear Leg to the Seat Rail Rail Pull Pin Rail Assembly can move freely Attach the Seat Rail to the Main AssemblyDo not over-tighten the hardware from Step 10a Attach the Leg Extension Pivot Tube Holes in the Leg Extension and cable end. Place 1 3/8 Attach Leg Cable to the Leg ExtensionSlide the hooked end of the Leg Cable beneath the Leg Thread the screw through Assemble the Leg Extension Seat Attach the Lat Cross Bar to the Upper Lat Tower Attach the Leg Extension Seat to the Main AssemblyPlace 2 3/8 Washers Item #N over the ends Attach the Upper Lat Tower to the Lower Attach the Rod Box with Power Rods to the Rod Box Frame Attach the Rod Box Frame to the Lat Tower Attach the Faceplate to the Main AssemblyBe tightened during Step #A, as shown in , attaching one side at a time Attach the Faceplate Back PanelsTighten Lower Bolt on the Seat Bracket Them until the panels meet in the center Repeat for remaining Chest Pulley Rod Cable Attach the Bench to the Seat AssemblyRoute the Rod Cables Locate the following items Repeat for remaining Squat Cable Route the Lat CablesRoute the Leg Cables Route the Squat Cables Offices in the United States International Offices Page Sport