Manuals / BOXLIGHT / Computer Equipment / Projector

BOXLIGHT MP-350m manual The time period that one horizontal line is displayed

Models: MP-350m

1 69

Download 69 pages 8.33 Kb

Page 41

U s i n g	t h e	P r o j e c t o r

Lamp hours used

Indicates how many hours the current lamp has been in use. The counter starts at zero hours and counts each hour the lamp is in use. When the counter reaches 3000 hours, the lamp monitor light turns on. For optimum results, the lamp should be replaced at this time. See “Replacing the Projection Lamp” on page 37 for details.

Computer resolution

Shows your computer’s resolution setting. To change this, go to your computer’s Control Panel and adjust the resolution in the Display tab. See your computer’s user’s guide for details.

Horizontal refresh rate

The time period that one horizontal line is displayed.

Vertical refresh rate

The time period that one video frame is displayed.

Mute status

Indicates if the audio is muted.

Software ver.

Indicates the projector’s software version. This information is useful when contacting Technical Support.

CablePro ver.

Indicates the CablePro’s software version. This information is useful when contacting Technical Support.

Source

Indicates the active source, Computer 1 (CablePro), Computer 2 (VESA input) or Video.

Speakers

Indicates if internal or external speakers are active.

34

Image 41

BOXLIGHT MP-350m manual The time period that one horizontal line is displayed

Contents

USER’S GUIDE BOXLIGHT MP-350m19332 Powder Hill Place Poulsbo, WA 98370-7407 USA Direct PhoneRemote Control Warning Safety CertificationsFCC Warning DOC CanadaTrademarks Declaration of ConformitySafety Instructions TABLE OF CONTENTSSetting up the Projector Using the ProjectorIndex Maintenance & TroubleshootingAppendix Warning Don’t block ventilation openings SAFETY INSTRUCTIONSWarning Hot surface. Do not touch INTRODUCTION Image ResolutionCompatibility Unpacking the Projectorshipping box may vary depending on the configuration you’ve ordered NOTE The contents of yourShipping box contents I n t r o d u c t i o nNOTE We recommend that you wait 30 seconds before powering Usage GuidelinesProjector up the projector after shutting it downIf You Need Assistance WarrantySETTING UP THE PROJECTOR S e t t i n g Connecting the CableProIII to the Projectort h e P r o j e c t o rPage Preparing to Connect Your Equipment to the ProjectorEquipment you want to connect Do you want to play your computer’s audio on the projector? Connecting a Laptop ComputerIf your computer has a PS/2 connector, use the PS/2 cable audio cable mouse cable Connecting the CablePro audio and mouse cables to a laptop computerNOTE The USB mouse is sup- ported for use with Windows 98 only Connecting a Desktop Computer audio cable mouse cable monitor cable Connecting the VESA computer cable to a computer Connecting a Computer Using a VESA cableaudio/video cable Connecting a Video PlayerS-video cable A/V cable Powering up the Projector and Adjusting the Image Connecting an External SpeakerTurning Off the Projector Using the Remote Control USING THE PROJECTORBasic Image Adjustment on underside of remote Remote controllaser pointer disk mouse right mouse button left mouse button Leveling knob Adjusting the ProjectorFocus ring, zoom ring, and elevator button To raise the projector 1 Press and hold the elevator button Figure Remote Using the Remote and Keypad ButtonsKeypad Adjusting the brightness lightens or darkens the image Volume + or PowerStandby VideoDrop-down menu Using the On-Screen MenusDisplay Menu Functions Reset All Color TemperatureColor Blank ScreenAudio Menu Functions Fade BalanceImage Menu Functions NOTE The Manual Sync, Manual Tracking, Horiz buttons are available only for computer sources. The projectorsets these options automatically for a video source Video Standard Controls Menu FunctionsStandby Time Ceiling ProjectionAuto Source Select Default SourcePlug and Play Display MessagesStatus menu Language menuLanguage menu Status menuThe time period that one horizontal line is displayed Cleaning the Fan Intake Filter MAINTENANCE & TROUBLESHOOTINGCleaning the Lens Use a vacuum cleaner set on low power to remove the dust and dirt 4 Clean the filterT r o u b l e s h o o t i n g Cleaning the air filterReplacing the Projection Lamp 6 Remove the module Figure Using the Kensington Lock Replacing the Batteries in the Remote ControlTroubleshooting Solutions to Common Problems If you’re using Windows Problem Image is out of focus Problem Image is too wide or narrow for screenProblem Image and menus are reversed left to right Problem Image and menus are upside downProblem Lamp seems to be getting dimmer Problem Image is “noisy” or streakedProblem Lamp shuts off Problem Remote not operating correctlythe projector’s serial number located on the bottom label the resolution of your computer Call Boxlight atTemperature APPENDIX SpecificationsDimensions WeightVideo Audio Input A p p e n d iCablePro Audio Input Audio OutputStandard Accessories ship with the projector AccessoriesPower Cords one ships with projector, type depends on country NOTE Use only Boxlight approved accessories. Other prodA p p e n d i Optional AccessoriesPortable and Laptop Activation Chart Key command to Key command toA p p e n d i ComputerKey command to Key command toComputer activate portKey command to Key command toA p p e n d i ComputerUsing Video Mirroring with a PowerBook Computer Projected image size Projected Image SizeA p p e n d i Image Size Image Size, Width and Height for Lens at MaximumDistance to DiagonalINDEX I n d e Page I n d e WARRANTY LIMITATION AND EXCLUSION LIMITED WARRANTYDISCLAIMER OF UNSTATED WARRANTIES LIMITATION OF LIABILITYPart Number