Names and functions of each part (continued)
Remote control transmitter
VIDEO, RGB button
Press to switch the input. (Refer to page 13, 19.) | VIDEO | RGB |
| LASER | |
STANDBY / ON button | STANDBY/ON | POSITION |
Used to turn the power on and off.
Press for 1 sec. or more to turn the power off (enter standby status).
(Refer to pages13 and 14.)
LASER button
Turns the laser beam on and off. Refer to page 11 conceming usage and observe the cautions.
*POSITION button
Press Position, then use the mouse Disk Pad to adjust the image position (RGB mode only).
(Refer to page 16.)
*DISK PAD / MOUSE button *4
(1)Used to select menu items when the menu screen is displayed (refer to page 16 - 18).
(2)When the menu is not displayed, the mouse shift function and left click function are active.
*1 (3) After the POSITION button has been pressed, the screen can be moved upward, downward and to the left and right.
RESET
MENU
FREEZE
MAGNIFY VOLUME
OFF
*RESET / MOUSE RIGHT button
(1)Operates as the RESET button when the menu is displayed. Press this button to return to the initial settings.
(2)Used to click the right mouse button when the menu is not displayed (refer to page 25,26).
*1 (3)Pressing this button after scrolling the screen with POSITION returns the screen to the original position.
*MENU button
Used to turn the menu screen display on and off. (Refer to page 17 - 21.)
*MAGNIFY button
Used to magnify the displayed image. (Refer to page 16.)
*P in P button *2
Used to turn P in P (Picture In Picture: displays sub video signal images in the RGB signal) on and off.
Each time this button is pressed, operation will change in the following sequence:
(1) Reduce sub screen
(2) Magnify sub screen
(3)Off.
(1) ∼ (3)
(Refer to page 20.)
BLANK button
Used to turn blanking on and off. (Refer to page 20.)
FOCUS button
Used to adjust the focus of the image on the screen. (Refer to page 13.)
P in P | MUTE |
BLANK AUTO TIMER
FOCUSZOOM
*FREEZE button
Used to turn the freeze (still) image display on and off. (Refer to page 15.)
VOLUME button
Adjusts the volume of the sound. Press [ ] to increase the volume and ( ) to decrease the volume. When there is no video signal input, operation is not possible when the input video signal is outside the sync range.
*MUTE button
Applies Mute. (Press the MUTE button again to cancel.)
TIMER button
Turns the display of the time set with the Timer on the Menu screen on and off.
The timer is not displayed when no input signal is detected or when SYNC is out of range or during blanking or during freezing.
Refer to page 21 concerning the method used to set the timer.
ZOOM button
Used to adjust the size of the image. (Refer to page 13.)
*AUTO button
Used to execute
*These functions do not operate when initial screen message “NO INPUT IS DETECTED” or “SYNC IS OUT OF RANGE” is displayed.
*1 POSITION icon | *3 Auto adjustment function |
When the POSITION button is pressed, the moving display icon will appear at the bottom right of the screen.
While displaying the icon, you can operate POSITION.
The projector automatically adjusts 4 items (V. POSIT, H. POSIT, H. PHASE, H. SIZE).
When you choose AUTO (move the cursor to the right from the manual operation position), the AUTO confirmation menu is shown.
*4 Disk Pad method of operation
•Move and select by tilting Disk Pad in the required direction.
•Press Disk Pad in to realize the function of the mouse left button.
•A mouse cable is necessary if a mouse is to be used. (Refer to pages 26, 27.)
*2 P in P function
With the P in P function, signals are input to both RGB and VIDEO. This function operates only when the RGB signal has been selected. There is no display in the case of the no signal and when the RGB signal is outside the sync range.
When P in P is used, audio is automatically switched to video.
In P in P, audio input can be switched by pressing the VOL 
and VOL 
keys of the remote control, displaying the audio bar and moving DISK PAD left and right during the display.
R G B / V I D E O
10
