Free-motion quilting, 1holder | Brother CS 80 guide

S2_brotherE.book Page 83 Thursday, February 13, 2003 11:03 AM

■Using the optional quilting guide

Use the quilting guide to sew parallel stitches that are equally spaced.

1Insert the stem of the quilter into the hole at the rear of the walking foot or presser foot holder.

Walking foot

Presser foot holder

2Adjust the stem of the quilter so that the quilt guide aligns with the seam that has already been sewn.

Free-motion quilting

With free-motion quilting, the feed dogs can be lowered (using the drop feed lever) so that the fabric can be moved freely in any direction.

The optional quilting foot is needed for free-motion quilting.

Remove the presser foot and the presser foot
1holder.
• Refer to “ Removing the presser foot holder”	3
(page 37).	3

2Align the quilting foot with the lower-left side of the presser bar.

The pin on the quilting foot should be positioned over the needle clamp screw.

1

2

3

1Pin on quilting foot

2Presser foot holder screw

3 Needle clamp screw

3Hold the quilting foot in place with your right hand, and then tighten the presser foot holder screw using the screwdriver in your left hand.

1

1Presser foot holder screw

CAUTION

●Be sure to securely tighten the screws with the screwdriver, otherwise the needle may touch the presser foot, causing it to bend or break.

Appliqué, Patchwork and Quilt Stitching 83

Image 89

Brother CS 80 manual Free-motion quilting, Using the optional quilting guide, Walking foot Presser foot holder, 1holder

Contents

DIC181p Accessories Enclosed Accessories Front view Names of Machine Parts and Their Functions Presser foot Needle and presser foot section Right-side/rear view Operation buttons Thread cassette indicator Stitches Operation panel Following are available as optional accessories Optional Accessories Introduction Sewing Machine Features Contents Adjusting the Stitch Width and Length Adjusting the Thread TensionSewing Useful Sewing Tips Maintenance Stitch SettingsTroubleshooting Error messages Important Safety Instructions For Users in the UK, EIRE, Malta and Cyprus only Congratulations on Choosing OUR Machine Getting Ready Turning the Machine On/Off Power supply precautions 4Unplug the power supply cord from the power supply jack 3Unplug the power supply cord from the electrical outletTurning on the machine Turning off the machine Bobbin precautions Winding/Installing the BobbinWinding the bobbin Move the bobbin thread spool pin up as far as possible Winding/Installing the Bobbin Thread is cut to a suitable length Sewing machine stops BPress start/stop button once Slide the bobbin cover latch to the right Installing the bobbin 7Reattach the bobbin cover About the spool of thread Upper ThreadingSpools that can be loaded into the thread cassette Spools that cannot be loaded into the thread cassette Upper Threading Loading the spool into the thread cassette Place the spool for the upper thread onto the spool pin Thread cassette is raised Follow arrow 5 indicated on the thread cassette Follow arrow 2 indicated on the thread cassette Spool of thread is now loaded in the thread cassette Check that the thread cassette indicator is lit up in greenThreading the needle Upper threading is finished 5Close the thread cassette compartment cover Using the extra spool pin1Placepin. the spool of thread onto the extra spool For more details, refer to About the spool of thread 3Install a needle Extra spool pin is now installedRemove the needle Refer to Replacing the needle For details, refer to Replacing the needle Using the twin needle Turnstitch.on the sewing machine, and then select a Install the twin needleFor details, refer to Thread the needle manually S2brotherE.book Page 28 Thursday, February 13, 2003 1103 AM Insert the bobbin into the shuttle Refer to steps 1 through 5 of Installing the bobbinPulling up the bobbin thread Replacing the Needle Needle precautionsNeedle types and their uses Fabrics Incorrect needle Checking the needleCorrect needle Checking the needle Replacing the needle 3Using the screwdriver, loosen the needle clamp screw Install the twin needle in the same way 4Lower the needle-changing tool Needle is installedNeedle can be removed from the needle bar 8Lowerneedle.the needle-changing tool off Replacing the presser foot Presser foot precautionsReplacing the Presser Foot Presser foot is attached Presser foot holder releases the presser foot For details, refer to Replacing the presser foot Removing the presser foot holderRemoving the presser foot holder 1Remove the presser foot 2Turn off the sewing machine Using the optional walking footAttaching the walking foot 1Remove the presser foot holder For details, refer to Removing the presser foot holder 5Attach the presser foot holder Free-arm sewing Sewing Cylindrical PiecesSlide the flap off to the left With the flap removed, free-arm sewing is possible Sewing Basics Sewing General sewing procedure Turn on the sewing machine Positioning the fabric3Place the fabric under the presser foot Fabric is now positioned to be sewn Starting to sew Machine stops sewing with the needle lowered in the fabric For details, refer to Starting to sew Machine starts sewing Securing the stitchingMachine stops sewing Machine starts sewing in the normal sewing direction Sewing reinforcement stitches Release the start/stop button or foot controller Cutting the thread When you have finished sewing, cut the threads2Raise the presser foot lever Threads are cut and the needle is raised Changing the tension of the upper thread Adjusting the Thread TensionCorrect thread tension Upper thread is too tight Adjusting the stitch width Adjusting the Stitch Width and LengthStitch width adjustment indicator lights up Changing the needle position Stitch length adjustment indicator lights up Adjusting the stitch length Trial sewing Useful Sewing TipsChanging the sewing direction Sewing curves Sewing thick fabrics Sewing stretch fabrics Sewing thin fabricsSewing an even seam allowance Aligning the fabric with the presser foot S2brotherE.book Page 56 Thursday, February 13, 2003 1103 AM Utility Stitches Selecting Stitching 6Iflength,necessary,etc. width and length adjust the stitchSelecting stitching Attach the presser foot Selecting Stitching Overcasting Stitches Sewing overcasting stitches using overcasting foot GStitch Attach overcasting foot G Preventing fraying center baseline Sewing overcasting stitches using zigzag foot JReverse stitching Stretch fabrics Fabric Sewing overcasting stitches using the optional side cutterSewing zigzag stitches while cutting Fabric Remove the presser foot Guide plate Basic Stitching When sewing is finished, cut the threadBasic stitching Position Blind Hem Stitching Sew a blind hem according to the following procedureFor details, refer to Replacing the presser Position the fabric with the edge of the folded If the needle catches too much of the hem fold Buttonhole Buttonhole Stitching Buttonhole sewing Size of the buttonhole is set If the button does not fit in the button guide plate3Attach buttonhole foot a 4Select a stitch Changing the stitch width For details, refer to Adjusting the stitch width Sewing buttonholes on stretch fabrics Button sewingTo the right as Seen from the front of the machine Attach button-sewing foot M 9Start Aftersewing.sewing for about 10 seconds at low Place the button into button-sewing foot M5Select stitch Zipper can be sewn in place Zipper InsertionInserting a centered zipper 6Select stitch Inserting a side zipper Wrong side of fabric Mm 1/8 inch 7Select stitch BTopstitch around the zipper Stretch stitching Elastic attaching Sewing Stretch Fabrics and Elastic Tape 3Select stitch Quilting Appliqué, Patchwork and Quilt Stitching 4Attach zigzag foot J Select a stitch Appliqué stitchingRemove the thick paper after pressing the seam allowance Patchwork crazy quilt stitching Edge of the fabric, and sew using stitchPiecing 3Select stitch or Baste the fabric to be quilted Attach the walking foot For details, refer to Using the optional walking footQuilting Free-motion quilting Using the optional quilting guideWalking foot Presser foot holder 1holder Normally, the drop feed lever is positioned at the left 4Slide the drop feed lever, located at the rear Triple stretch stitching Bar tack stitching Reinforcement StitchingInseams Reinforcing the ends of openings 5Pullpossible.down the buttonhole lever as far as Attach monogramming foot N 3Adjust the stitch width to select the desired eyelet sizeEyelet Stitching Decorative Decorative Stitching 3Attach zigzag foot J Fagoting4Select stitch Set the stitch width to 7.0 mm 1/4 inch Smocking Scallop stitching4Trim along the stitches 3Sew parallel stitching at intervals of 1 cm 3/8 inch 3Select stitch , or Joining Heirloom stitching 4Sew along the center of the unfrayed section S2brotherE.book Page 94 Thursday, February 13, 2003 1103 AM Appendix Stitch Settings Maintenance Utility stitches Stitch Settings Stitch Settings Appliqué stitch For quilting Pattern Cleaning the machine surface MaintenanceCleaning the shuttle Needle plate cover is removed Do not apply oil to the shuttle Remove the shuttleGrasp the shuttle, and then pull it out Loosen the upper thread tension TroubleshootingPresser foot lever is raised Lower the presser foot lever Correctly install the presser foot Clean the shuttle Bobbin designed specifically forShuttle Needle is bent or blunt Replace the needle Thread tension is incorrect Adjust the tension of the upper Authorized service center Bobbin designed specifically forNeedle was not raised Red Green Sewing lamp is damaged Contact your retailer or the nearest Operation beep Error messagesIf you press Message disappears Needle stop position changes to the raised position Changing the needle stop position Numerics Index Index