![DILUTION SOLENOID VALVE](/images/new-backgrounds/63159/6315947x1.webp)
SERVICE (cont.) | 5. | Check the solenoid valve for coil action. Connect | |
DILUTION SOLENOID VALVE |
| the brewer to the power source, place the TEA/ | |
| OFF/COFFEE switch in the “TEA” position and mo- | ||
|
|
| |
|
|
| mentarily place the START switch in the lower po- |
|
|
| sition and release. Listen carefully in the vicinity |
|
|
| of the solenoid valve for a “clicking” sound as the |
|
|
| coil magnet attracts. |
|
| 6. | Disconnect the brewer from the power source. |
|
| If the sound is heard as described and water will not | |
|
| pass through the solenoid valve, there may be a block- | |
|
| age in the water line before or after the solenoid valve | |
|
| or, the solenoid valve may require inspection for wear, | |
|
| and removal of waterborne particles. | |
|
| If the sound is not heard as described, replace the | |
|
| solenoid valve. | |
| P2198.50 | Removal and Replacement: | |
| FIG. 16 DILUTION SOLENOID VALVE | 1. | Remove all wires from the solenoid valves. |
| 2. | Turn off the water supply to the brewer. | |
|
| ||
Location: | 3. | Disconnect the water lines to and from the sole- | |
| Viewing the brewer from the rear the dilution so- |
| noid valves. |
lenoid is mounted on the right side of the solenoid | 4. | Remove the two | |
mounting bracket which is secured to the trunk base. | 5. | mounting bracket to the trunk base. | |
|
| Lift out the bracket. | |
Test Procedure: | 6. | Remove the two | |
1. Disconnect the brewer from the power source. |
| ing the solenoid valve to the mounting bracket. | |
2. | With a voltmeter, check the voltage across the | 7. | Securely install the new solenoid valve to the |
| white/blue and white/violet wires on the dilution |
| mounting bracket. |
| solenoid terminals when the TEA/OFF/COFFEE | 8. | Attach the mounting bracket to the trunk base. |
| switch is in the “TEA” position and the START | 9. | Securely fasten the water lines to and from the |
| switch is momentarily placed in the lower posi- |
| solenoid valves. |
| tion. Connect the brewer to the power source. | 10. | Refer to Fig. 17 when reconnecting the wires. |
| The indication must be 120 volts ac for two wire |
|
|
| 120 volt models and three wire 120/208 volt mod- |
|
|
| els. |
| WHI/BLU to Iced |
3. Disconnect the brewer from the power supply. |
| ||
| Tea Brew Timer | ||
|
|
| |
|
|
| TL4 |
If voltage is present as described, proceed to #4.
If voltage is not present as described, refer to the Wir- ing Diagrams and check the wiring harness.
|
| WHI/VIO to Iced | |
4. Remove both wires from the coil and check for | HOT COFFEE | Tea Brew Timer | |
TL1 |
| ||
continuity across the coil terminals. | BREW SOLENOID |
| |
ICED TEA BREW |
|
| |
|
|
| |
| SOLENOID |
|
|
If continuity is present as described, reconnect the |
| DILUTION |
|
white/blue and white/violet wires and proceed to #5. |
|
| |
| SOLENOID |
| |
If continuity is not present as described, replace the |
| P1364 | |
|
| ||
solenoid valve. | FIG.17 SOLENOID VALVE TERMINALS |
| |
Page 24 | 10510 | 081599 | |
|
|