Cabletron Systems BRIM-F6

Installing an HSIM

HSIM-F6 User’s Guide 2-5

4. Slide out the module, and place it on its side with the internal

components facing up.

5. Refer to Figure 2-3 and remove the two faceplate mounting screws

and the HSIM coverplate. Save the screws.

6. Refer to Figure 2-3 and remove the two standoff screws. Save the

screws.

Figure 2-3 Removing the HSIM Coverplate

7. Refer to Figure 2-4 and place the HSIM behind the module faceplate.

8. Align the HSIM connector of the HSIM-F6 into the HSIM pins on the

module.

Standoff Screws

Faceplate Mounting

Screws

Coverplate

209135

Contents

Main Page HSIM-F6 Users Guide i FCC NOTICE NOTICE Only qualied personnel should perform installation procedures. ii HSIM-F6 Users Guide HSIM-F6 Users Guide iii UNITED STATES GOVERNMENT RESTRICTED RIGHTS EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITY CABLETRON SOFTWARE PROGRAM LICENSE iv HSIM-F6 Users Guide HSIM-F6 Users Guide v DECLARATION OF CONFORMITY Page HSIM-F6 Users Guide vii CONTENTS Contents viii HSIM-F6 Users Guide CHAPTER 1 INTRODUCTION 1.1 USING THIS MANUAL 1.2 DOCUMENT CONVENTIONS 1.3 GETTING HELP 1.4 OVERVIEW 1.4.1 Features 1.5 SPECIFICATIONS 1.6 RELATED DOCUMENTATION CHAPTER 2 INSTALLATION 2.1 UNPACKING THE HSIM 2.2 INSTALLING FPIMs Installing FPIMs HSIM-F6 Users Guide 2-3 Figure 2-1 Removing the FPIM Coverplate Figure 2-2 Installing FPIMs 2.3 INSTALLING AN HSIM 2.3.1 Installing an HSIM in an Interface Module Page Page 2.3.2 Installing an HSIM in a Standalone Hub Page CHAPTER 3 LOCAL MANAGEMENT Chapter 3: Local Management 3-2 HSIM-F6 Users Guide 3.1 LOCAL MANAGEMENT KEYBOARD CONVENTIONS 3.1.1 Selecting Local Management Menu Screen Items 3.1.2 Exiting Local Management Screens 3.2 NAVIGATING LOCAL MANAGEMENT SCREENS 3.3 THE HSIM-F6 SETUP SCREEN Page Page 3.4 THE HSIM-F6 STATISTICS SCREEN 3.4.1 HSIM-F6 Statistics Screen Fields 3.5 THE MIB-II STATISTICS SCREEN 3.5.1 MIB-II Interface Statistics Screen Fields 3.6 THE RING STATISTICS SCREEN 3.6.1 HSIM-F6 FDDI Ring Statistics Screen Fields Page Page Page Page 3.7 THE RING MAP CONFIGURATION SCREEN 3.7.1 Ring Map Conguration Screen Fields 3.7.2 Ring Map Conguration Screen Commands n 3.7.2.1 Adjusting the Scroll Number ( ) The Ring Map Conguration Screen HSIM-F6 Users Guide 3-19 3.7.3 The Node Information Screen Figure 3-12 The Ring Map Node Information Screen NOTE The Ring Map Node Information screen reects node status at 3.7.4 Node Information Screen Fields 3.8 THE HSIM-F6 CONFIGURATION SCREEN 3.8.1 HSIM-F6 Conguration Screen Fields 3.9 THE FULL DUPLEX CONFIGURATION SCREEN 3.9.1 Full Duplex FDDI 3.9.2 Full Duplex Conguration Screen Fields 3.9.3 Conguring the HSIM-F6 for Full Duplex Operation 3.10 THE FDDI/ETHERNET TRANSLATION CONFIGURATION SCREEN 3.10.1 FDDI Translation Conguration Screen Fields Page 3.10.2 Setting Frame Translation Types Page Page HSIM-F6 Users Guide 4-1 CHAPTER 4 LANVIEW LEDs Page 4.1 HSIM-F6 LED STATE DEFINITIONS Page Page Page HSIM-F6 Users Guide 5-1 CHAPTER 5 SPECIFICATIONS 5.1 FIBER OPTIC INTERFACE Depending on the FPIM, interfaces have the following characteristics: 5.1.1 Multimode Specications Chapter 5: Specications 5.1.2 Single Mode Specications 5-2 HSIM-F6 Users Guide Page Chapter 5: Specications 5-4 HSIM-F6 Users Guide 5.2 UNSHIELDED TWISTED PAIR (UTP) SPECIFICATIONS Shielded Twisted Pair (STP) Transmitter Specications HSIM-F6 Users Guide 5-5 5.3 SHIELDED TWISTED PAIR (STP) TRANSMITTER SPECIFICATIONS 5.4 CABLE SPECIFICATIONS 5.4.1 Multimode Fiber Optic Cable Length 5.4.2 Single Mode Fiber Optic Cable Length 5.4.3 Twisted Pair Cable Length 5.5 TWISTED PAIR PINOUT CONFIGURATION Page APPENDIX A FPIM SPECIFICATIONS A.1 FPIM-00 AND FPIM-01 A.2 FPIM-02 AND FPIM-04 A.3 FPIM-05 AND FPIM-07