Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems FDDI manual FPIM-02 and FPIM-04

Models: FDDI

1 32

Download 32 pages 27.98 Kb

Page 16

Chapter 2: Network Requirements

Table 2-2 Transmitter Power Parameters

			Worst	Worst	Typical
	Parameter	Typical Value	Worst	Case	Typical
	Parameter	Typical Value	Case	Case	Budget
			Case	Budget	Budget
				Budget


	50/125 ∝m	-13.0 dBm	-15.0 dBm	13.0 dB	17.5 dB
	ﬁber

	62.5/125	-10.0 dBm	-12.0 dBm	16.0 dB	20.5 dB
	∝m ﬁber

	100/140 ∝m	-7.0 dBm	-9.0 dBm	19.0 dB	23.5 dB
	ﬁber

	Error Rate	Better than 10-10

The link distance is up to 2 kilometers on the multimode ﬁber optic cable as speciﬁed by ANSI MMF-PMD.

2.1.2FPIM-02 and FPIM-04

The FPIM-02 has an RJ-45 connector supporting an Unshielded Twisted Pair (UTP) connection. The FPIM-04 has an RJ-45 connector supporting a Shielded Twisted Pair (STP) connection. The pinouts for both are listed in Table 2-3.

Table 2-3 FPIM-02 and FPIM-04 Pinouts

Pin Number	Represents	Pin Number	Represents


1	Transmit+	5	NA

2	Transmit-	6	NA

3	NA	7	Receive+

4	NA	8	Receive-

The link distance is up to 100 meters on unshielded twisted pair cable as speciﬁed by ANSI TP-PMD.

2-2 7F06-02 FDDI SmartSwitch Interface Module User’s Guide

Image 16

Cabletron Systems manual FPIM-02 and FPIM-04, 2-2 7F06-02 FDDI SmartSwitch Interface Module User’s Guide

Contents

7F06-02 FDDI SmartSwitch Interface Module User’s GuidePage 7F06-02 FDDI SmartSwitch Interface Module User’s Guide FCC NOTICE7F06-02 FDDI SmartSwitch Interface Module User’s Guide DOC NOTICEVCCI NOTICE CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENTEXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITY 7F06-02 FDDI SmartSwitch Interface Module User’s GuideCABLETRON SOFTWARE PROGRAM LICENSE UNITED STATES GOVERNMENT RESTRICTED RIGHTS7F06-02 FDDI SmartSwitch Interface Module User’s Guide DECLARATION OF CONFORMITYCONTENTS INSTALLATION/REMOVALTROUBLESHOOTING 7F06-02 FDDI SmartSwitch Interface Module User’s GuideContents TECHNICAL SPECIFICATIONS7F06-02 FDDI SmartSwitch Interface Module User’s Guide SafetyCHAPTER INTRODUCTION 1.1 USING THIS MANUAL1.2 THE 7F06-02 MODULE 1.2.1 Cable Type and FPIMs 1-2 7F06-02 FDDI SmartSwitch Interface Module User’s Guide1.3.1 FPIMs 1.3 FEATURES1.3.2 LANVIEW LEDs 1.3.3 Connectivity 1.4 RELATED MANUALS1.5 GETTING HELP Service and Support1-6 7F06-02 FDDI SmartSwitch Interface Module User’s Guide Chapter 1 IntroductionCHAPTER NETWORK REQUIREMENTS 2.1 FPIM MODULE SPECIFICATIONS2.1.1 FPIM-00 and FPIM-01 2.1.2 FPIM-02 and FPIM-04 2-2 7F06-02 FDDI SmartSwitch Interface Module User’s Guide2.1.3 FPIM-05 and FPIM-07 Table 2-4 FPIM-05 and FPIM-07 Speciﬁcations2-4 7F06-02 FDDI SmartSwitch Interface Module User’s Guide Chapter 2 Network RequirementsCHAPTER INSTALLATION/REMOVAL 3.1 UNPACKING THE 7F06-02 MODULE3.2 INSTALLING FPIMS 3.3 INSTALLING/REMOVING THE 7F06-02 MODULE 3.3.1 Installing in the 7C03 SmartSwitch3.3.2 Removing from the 7C03 SmartSwitch 3-4 7F06-02 FDDI SmartSwitch Interface Module User’s Guide3.3.3 Installing in the 7C04 or 7C04-R Workgroup SmartSwitch Chapter 3 Installation/Removal 3-6 7F06-02 FDDI SmartSwitch Interface Module User’s GuideFigure 3-4 Installing the 7F06-02 Module in the 7C04 Workgroup SmartSwitchScrews Ejector TabsChapter 3 Installation/Removal 3-8 7F06-02 FDDI SmartSwitch Interface Module User’s GuideSmartSwitch Screws4.1 DIAGNOSTIC AND MONITORING SYSTEM CHAPTER TROUBLESHOOTINGF D D 4.2 PORT RECEIVE LEDS 4.3 PORT TRANSMIT LEDS4.4 A/B LINK LEDS Chapter 4 TroubleshootingChapter 4 Troubleshooting 7F06-02 FDDI SmartSwitch Interface Module User’s GuideState Table 4-3 Link LEDs ContinuedChapter 4 Troubleshooting 4-4 7F06-02 FDDI SmartSwitch Interface Module User’s GuideCHAPTER TECHNICAL SPECIFICATIONS 5.1 STANDARDS5.2 EMI 5.3 EMC5.5 SAFETY 5.6 SERVICE5.7 PHYSICAL 5.7.1 Dimensions 5.7.2 Weight