Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems FDDI manual Chapter Network Requirements, Fpim Module Specifications

Models: FDDI

1 32

Download 32 pages 27.98 Kb

Page 15

CHAPTER 2

NETWORK REQUIREMENTS

Before installing Cabletron Systems 7F06-02 Module, review the network requirements outlined in this chapter. All requirements included in this chapter should be met to ensure satisfactory performance of the 7F06-02 Module. Failure to do so may result in unsatisfactory network performance.

2.1FPIM MODULE SPECIFICATIONS

This module uses Fiber Port Interface Modules (FPIM) to provide front panel cable connections. The FPIMs are user-installable. Refer to Section 3.2, Installing FPIMs.

2.1.1FPIM-00 and FPIM-01

The FPIM-00 and FPIM-01 provide a multimode ﬁber connection. The FPIM-00 uses a MIC style connector and the FPIM-01 uses an SC type connector. The speciﬁcations for both devices are listed in Table 2-1, while the transmitter power parameters are provided in Table 2-2.

Table 2-1 FPIM-00 and FPIM-01 Speciﬁcations

			Worst	Worst	Typical
	Parameter	Typical Value	Worst	Case	Typical
	Parameter	Typical Value	Case	Case	Budget
			Case	Budget	Budget
				Budget


	Receive	-30.5 dBm	-28.0 dBm	—	—
	Sensitivity

	Peak Input	-7.6 dBm	-8.2 dBm	—	—
	Power

7F06-02 FDDI SmartSwitch Interface Module User’s Guide

2-1

Image 15

Cabletron Systems FDDI manual Chapter Network Requirements, Fpim Module Specifications, FPIM-00 and FPIM-01

Contents

Interface Module User’s Guide 7F06-02 FDDI SmartSwitchPage FCC NOTICE 7F06-02 FDDI SmartSwitch Interface Module User’s GuideCABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT 7F06-02 FDDI SmartSwitch Interface Module User’s GuideDOC NOTICE VCCI NOTICEUNITED STATES GOVERNMENT RESTRICTED RIGHTS EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITY7F06-02 FDDI SmartSwitch Interface Module User’s Guide CABLETRON SOFTWARE PROGRAM LICENSEDECLARATION OF CONFORMITY 7F06-02 FDDI SmartSwitch Interface Module User’s Guide7F06-02 FDDI SmartSwitch Interface Module User’s Guide CONTENTSINSTALLATION/REMOVAL TROUBLESHOOTINGSafety ContentsTECHNICAL SPECIFICATIONS 7F06-02 FDDI SmartSwitch Interface Module User’s Guide1.1 USING THIS MANUAL CHAPTER INTRODUCTION1.2 THE 7F06-02 MODULE 1-2 7F06-02 FDDI SmartSwitch Interface Module User’s Guide 1.2.1 Cable Type and FPIMs1.3 FEATURES 1.3.1 FPIMs1.3.2 LANVIEW LEDs 1.4 RELATED MANUALS 1.3.3 ConnectivityService and Support 1.5 GETTING HELPChapter 1 Introduction 1-6 7F06-02 FDDI SmartSwitch Interface Module User’s Guide2.1 FPIM MODULE SPECIFICATIONS CHAPTER NETWORK REQUIREMENTS2.1.1 FPIM-00 and FPIM-01 2-2 7F06-02 FDDI SmartSwitch Interface Module User’s Guide 2.1.2 FPIM-02 and FPIM-04Table 2-4 FPIM-05 and FPIM-07 Speciﬁcations 2.1.3 FPIM-05 and FPIM-07Chapter 2 Network Requirements 2-4 7F06-02 FDDI SmartSwitch Interface Module User’s Guide3.1 UNPACKING THE 7F06-02 MODULE CHAPTER INSTALLATION/REMOVAL3.2 INSTALLING FPIMS 3.3.1 Installing in the 7C03 SmartSwitch 3.3 INSTALLING/REMOVING THE 7F06-02 MODULE3-4 7F06-02 FDDI SmartSwitch Interface Module User’s Guide 3.3.2 Removing from the 7C03 SmartSwitch3.3.3 Installing in the 7C04 or 7C04-R Workgroup SmartSwitch SmartSwitch Chapter 3 Installation/Removal3-6 7F06-02 FDDI SmartSwitch Interface Module User’s Guide Figure 3-4 Installing the 7F06-02 Module in the 7C04 WorkgroupEjector Tabs ScrewsScrews Chapter 3 Installation/Removal3-8 7F06-02 FDDI SmartSwitch Interface Module User’s Guide SmartSwitchCHAPTER TROUBLESHOOTING 4.1 DIAGNOSTIC AND MONITORING SYSTEMF D D Chapter 4 Troubleshooting 4.2 PORT RECEIVE LEDS4.3 PORT TRANSMIT LEDS 4.4 A/B LINK LEDSTable 4-3 Link LEDs Continued Chapter 4 Troubleshooting7F06-02 FDDI SmartSwitch Interface Module User’s Guide State4-4 7F06-02 FDDI SmartSwitch Interface Module User’s Guide Chapter 4 Troubleshooting5.3 EMC CHAPTER TECHNICAL SPECIFICATIONS5.1 STANDARDS 5.2 EMI5.7.2 Weight 5.5 SAFETY5.6 SERVICE 5.7 PHYSICAL 5.7.1 Dimensions