Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems FDDI manual Installing Fpims

Models: FDDI

1 32

Download 32 pages 27.98 Kb

Page 20

Image 20

Chapter 3: Installation/Removal

3.2INSTALLING FPIMS

Before installing the 7F06-02 module, attach the antistatic wrist strap included with the SmartSwitch or SmartSwitch module by following the instructions printed on the package.

The 7F06-02 module is shipped without FPIMs. To install an FPIM, follow the procedure below:

1.Remove the module if it is installed in the 7C03 MMAC SmartSwitch chassis by reversing the procedure in Section 3.3.

2.Remove the blank front cover over the FPIM slot.

3.Install the FPIM as shown in Figure 3-1. Ensure that the rear connector is seated firmly before tightening the two mounting screws.

Figure 3-1 Installing an FPIM

3-2 7F06-02 FDDI SmartSwitch Interface Module User’s Guide

Page 20

Image 20

Cabletron Systems FDDI manual Installing Fpims

Contents

7F06-02 FDDI SmartSwitch Interface Module User’s GuidePage 7F06-02 FDDI SmartSwitch Interface Module User’s Guide FCC NOTICE7F06-02 FDDI SmartSwitch Interface Module User’s Guide DOC NOTICEVCCI NOTICE CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENTEXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITY 7F06-02 FDDI SmartSwitch Interface Module User’s GuideCABLETRON SOFTWARE PROGRAM LICENSE UNITED STATES GOVERNMENT RESTRICTED RIGHTS7F06-02 FDDI SmartSwitch Interface Module User’s Guide DECLARATION OF CONFORMITYCONTENTS INSTALLATION/REMOVALTROUBLESHOOTING 7F06-02 FDDI SmartSwitch Interface Module User’s GuideContents TECHNICAL SPECIFICATIONS7F06-02 FDDI SmartSwitch Interface Module User’s Guide Safety1.2 THE 7F06-02 MODULE 1.1 USING THIS MANUALCHAPTER INTRODUCTION 1.2.1 Cable Type and FPIMs 1-2 7F06-02 FDDI SmartSwitch Interface Module User’s Guide1.3.2 LANVIEW LEDs 1.3 FEATURES1.3.1 FPIMs 1.3.3 Connectivity 1.4 RELATED MANUALS1.5 GETTING HELP Service and Support1-6 7F06-02 FDDI SmartSwitch Interface Module User’s Guide Chapter 1 Introduction2.1.1 FPIM-00 and FPIM-01 2.1 FPIM MODULE SPECIFICATIONSCHAPTER NETWORK REQUIREMENTS 2.1.2 FPIM-02 and FPIM-04 2-2 7F06-02 FDDI SmartSwitch Interface Module User’s Guide2.1.3 FPIM-05 and FPIM-07 Table 2-4 FPIM-05 and FPIM-07 Speciﬁcations2-4 7F06-02 FDDI SmartSwitch Interface Module User’s Guide Chapter 2 Network RequirementsCHAPTER INSTALLATION/REMOVAL 3.1 UNPACKING THE 7F06-02 MODULE3.2 INSTALLING FPIMS 3.3 INSTALLING/REMOVING THE 7F06-02 MODULE 3.3.1 Installing in the 7C03 SmartSwitch3.3.2 Removing from the 7C03 SmartSwitch 3-4 7F06-02 FDDI SmartSwitch Interface Module User’s Guide3.3.3 Installing in the 7C04 or 7C04-R Workgroup SmartSwitch Chapter 3 Installation/Removal 3-6 7F06-02 FDDI SmartSwitch Interface Module User’s GuideFigure 3-4 Installing the 7F06-02 Module in the 7C04 Workgroup SmartSwitchScrews Ejector TabsChapter 3 Installation/Removal 3-8 7F06-02 FDDI SmartSwitch Interface Module User’s GuideSmartSwitch ScrewsF D D CHAPTER TROUBLESHOOTING4.1 DIAGNOSTIC AND MONITORING SYSTEM 4.2 PORT RECEIVE LEDS 4.3 PORT TRANSMIT LEDS4.4 A/B LINK LEDS Chapter 4 TroubleshootingChapter 4 Troubleshooting 7F06-02 FDDI SmartSwitch Interface Module User’s GuideState Table 4-3 Link LEDs ContinuedChapter 4 Troubleshooting 4-4 7F06-02 FDDI SmartSwitch Interface Module User’s GuideCHAPTER TECHNICAL SPECIFICATIONS 5.1 STANDARDS5.2 EMI 5.3 EMC5.5 SAFETY 5.6 SERVICE5.7 PHYSICAL 5.7.1 Dimensions 5.7.2 Weight