Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems FDDI manual Removing from the 7C03 SmartSwitch

Models: FDDI

1 32

Download 32 pages 27.98 Kb

Page 22

3.3.2Removing from the 7C03 SmartSwitch

Chapter 3: Installation/Removal

3.3.2Removing from the 7C03 SmartSwitch

The 7F06-02 Module inserted in the 7C03 MMAC SmartSwitch can be removed upon proper removal of power. Follow the steps below and refer to Figure 3-3 to remove the module.

Note: Before removing the 7F06-02 module, attach the antistatic wrist strap included with the SmartSwitch or SmartSwitch module by following the instructions printed on the package.

1.As a precaution, power down the MMAC 8 before beginning the installation or removal of any modules. At the very minimum, the 7C03 must be pulled to disconnect it from the power source. Damage to modules may result if this procedure is not followed.

2.Use a slotted screwdriver to loosen the two screws that secure the module to the chassis.

3.Locate the two ejector tabs on the module (to the right of the screws on the top and bottom of the module).

4.Simultaneously press down on the bottom ejector tab and up on the top ejector tab until the module ejects from the backplane.

5.Grasp both ejector tabs and carefully slide the module out of the chassis.

Screw

Ejector Tab

Screw

Ejector Tab

Figure 3-3 Removing the 7F06-02 Module from the 7C03 MMAC

SmartSwitch

3-4 7F06-02 FDDI SmartSwitch Interface Module User’s Guide

Image 22

Cabletron Systems manual Removing from the 7C03 SmartSwitch, 3-4 7F06-02 FDDI SmartSwitch Interface Module User’s Guide

Contents

7F06-02 FDDI SmartSwitch Interface Module User’s GuidePage 7F06-02 FDDI SmartSwitch Interface Module User’s Guide FCC NOTICEVCCI NOTICE 7F06-02 FDDI SmartSwitch Interface Module User’s GuideDOC NOTICE CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENTCABLETRON SOFTWARE PROGRAM LICENSE EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITY7F06-02 FDDI SmartSwitch Interface Module User’s Guide UNITED STATES GOVERNMENT RESTRICTED RIGHTS7F06-02 FDDI SmartSwitch Interface Module User’s Guide DECLARATION OF CONFORMITYTROUBLESHOOTING CONTENTSINSTALLATION/REMOVAL 7F06-02 FDDI SmartSwitch Interface Module User’s Guide7F06-02 FDDI SmartSwitch Interface Module User’s Guide ContentsTECHNICAL SPECIFICATIONS SafetyCHAPTER INTRODUCTION 1.1 USING THIS MANUAL1.2 THE 7F06-02 MODULE 1.2.1 Cable Type and FPIMs 1-2 7F06-02 FDDI SmartSwitch Interface Module User’s Guide1.3.1 FPIMs 1.3 FEATURES1.3.2 LANVIEW LEDs 1.3.3 Connectivity 1.4 RELATED MANUALS1.5 GETTING HELP Service and Support1-6 7F06-02 FDDI SmartSwitch Interface Module User’s Guide Chapter 1 IntroductionCHAPTER NETWORK REQUIREMENTS 2.1 FPIM MODULE SPECIFICATIONS2.1.1 FPIM-00 and FPIM-01 2.1.2 FPIM-02 and FPIM-04 2-2 7F06-02 FDDI SmartSwitch Interface Module User’s Guide2.1.3 FPIM-05 and FPIM-07 Table 2-4 FPIM-05 and FPIM-07 Speciﬁcations2-4 7F06-02 FDDI SmartSwitch Interface Module User’s Guide Chapter 2 Network RequirementsCHAPTER INSTALLATION/REMOVAL 3.1 UNPACKING THE 7F06-02 MODULE3.2 INSTALLING FPIMS 3.3 INSTALLING/REMOVING THE 7F06-02 MODULE 3.3.1 Installing in the 7C03 SmartSwitch3.3.2 Removing from the 7C03 SmartSwitch 3-4 7F06-02 FDDI SmartSwitch Interface Module User’s Guide3.3.3 Installing in the 7C04 or 7C04-R Workgroup SmartSwitch Figure 3-4 Installing the 7F06-02 Module in the 7C04 Workgroup Chapter 3 Installation/Removal3-6 7F06-02 FDDI SmartSwitch Interface Module User’s Guide SmartSwitchScrews Ejector TabsSmartSwitch Chapter 3 Installation/Removal3-8 7F06-02 FDDI SmartSwitch Interface Module User’s Guide Screws4.1 DIAGNOSTIC AND MONITORING SYSTEM CHAPTER TROUBLESHOOTINGF D D 4.4 A/B LINK LEDS 4.2 PORT RECEIVE LEDS4.3 PORT TRANSMIT LEDS Chapter 4 TroubleshootingState Chapter 4 Troubleshooting7F06-02 FDDI SmartSwitch Interface Module User’s Guide Table 4-3 Link LEDs ContinuedChapter 4 Troubleshooting 4-4 7F06-02 FDDI SmartSwitch Interface Module User’s Guide5.2 EMI CHAPTER TECHNICAL SPECIFICATIONS5.1 STANDARDS 5.3 EMC5.7 PHYSICAL 5.7.1 Dimensions 5.5 SAFETY5.6 SERVICE 5.7.2 Weight