Installation Requirements and Handling

In order to use this machine in a safe and trouble-free manner, install the machine in a place that fulfills the following conditions. Also, read the remarks carefully.

Temperature and Humidity Conditions

•Temperature range: 50 to 86°F (10 to 30°C)•Humidity range: 20 to 80 % RH (no condensation)

IMPORTANT

Protecting the machine from condensation

•To prevent condensation from forming inside the machine in the following cases, let the machine adjust to the ambient temperature and humidity for at least two hours before use.

-When the room where the machine is installed is heated rapidly

-When the machine is moved from a cool or dry location to a hot or humid location

•If water droplets (condensation) form inside the machine, this can result in paper jams or poor print quality.

When using an ultrasonic humidifier

When you are using an ultrasonic humidifier, it is therefore recommended that you use purified water or other water that is free of impurities.

If you use tap water or well water, impurities in the water will be dispersed through the air. This can be trapped inside the machine, causing degradation in print quality.

Power Supply Requirements

120 to 127 V 60 Hz

IMPORTANT

Precautions when connecting the power cord•Do not connect this machine to an uninterruptible power source.

•Use an AC power outlet exclusively for the machine. Do not use the other sockets of the AC power outlet.

•Do not plug the power plug into the auxiliary outlet on a computer.

Do not use the same AC power outlet for both the machine and any of the following equipment.

-Copy machine-Air conditioner-Shredder-Equipment that consumes a large amount of electricity-Equipment that generates electrical noise

•When unplugging the power cord, keep interval of 5 sec- onds or more before plugging it again.

Miscellaneous precautions•The maximum power consumption of the machine is as follows.-MF8350Cdn: 1,200 W or less-MF8050Cn: 900 W or less

•Electrical noise or a dramatic drop in mains voltage may cause the machine or computer to operate incorrectly or lose data.

Installation Requirements

•A location with sufficient space•A location with good ventilation•A location with a flat, even surface•A location able to fully support the weight of the machine

IMPORTANT

Do not install the machine in the following locations, as this may result in damage to the machine.

•A location subject to dramatic changes in temperature or humidity•A location subject to condensation•A poorly ventilated location

(If you use the machine for a long time or to perform a large amount of printing in a poorly ventilated room, the ozone or other odors generated by the machine may create an uncomfortable working environment. In addition, chemical particles are dispersed during printing; therefore, it is impor- tant to provide adequate ventilation.)

•A location near equipment that generates magnetic or elec- tromagnetic waves•A laboratory or location where chemical reactions occur•A location exposed to salt air, corrosive gases, or toxic gases

•A location, such as on a carpet or mat, that may warp from the weight of the machine or where the machine is liable to sink

Installation Space

Required installation space

MF8350Cdn

Front View

 

 

 

 

 

 

in. (mm)

 

52 1/4 (1327)

(679)3/426

4

(100)

(851)1/233

(951)1/237

 

4

(100)

 

 

 

 

 

 

 

 

Feeder

 

Paper

 

 

Feeder cover

 

 

 

 

 

cassette

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

 

4

 

 

 

 

 

(100)

 

 

(100)

 

 

 

 

 

 

4

(100)

Rear cover

 

 

 

 

 

 

 

 

 

 

 

 

 

MF8050Cn

Front View

 

 

 

 

in. (mm)

 

48 3/8 (1229)

4 (100)

 

cassette

4

(100)

Feeder cover

Feeder

Paper

 

 

 

4

 

 

1/226(674)

 

1/231(801)

 

 

4

 

 

(100)

 

 

(100)

 

 

 

4

(100)

Rear cover

 

 

 

 

 

 

 

xi