Manuals / Carrier / Kitchen Appliance / Refrigerator

Carrier 17 Front View, Plan View, Ð Typical Insulation Area 19EX Shown

Models: 17 19EX

1 32

Download 32 pages 19.33 Kb

Page 30

Image 30

FRONT VIEW

Ð Area must be factory or ®eld insulated

Ð Area to be ®eld insulated, if ambient conditions require. NOTE: Waterbox covers are to be insulated by the contractor.

PLAN VIEW

IMPORTANT: 17EX insulation is identical to the 19EX insulation shown above. 17EX motors do not require insulation.

Fig. 24 Ð Typical Insulation Area (19EX Shown)

Manufacturer reserves the right to discontinue, or change at any time, speci®cations or designs without notice and without incurring obligations.

Book	2	2	PC 211	Catalog No. 531-749	Printed in U.S.A.	Form 17/19EX-2SI	Pg 30	3-96	Replaces: 17/19EX-1SI
Tab	5a	5d

Page 30

Image 30

Carrier 17 installation instructions Front View, Plan View, Ð Typical Insulation Area 19EX Shown

Contents

SAFETY CONSIDERATIONS Installation Instructions17/19EX 50/60 Hz Centrifugal Liquid Chillers with HFC-134a INTRODUCTION CONTENTSINSTALLATION Receiving the Machine Job Data`U STAMP Fig. 1 Ð Model Number IdenticationARI Air Conditioning and RefrigerationFig. 2 Ð Typical 19EX Installation 19EXLocal Interface Display Control Panel Fig. 3 Ð Typical 17EX Installation 19EX FRONT VIEW 17EX FRONT VIEWFig. 4 Ð 17EX Machine Rigging Guide Fig. 5 Ð 19EX Machine Rigging GuideFig. 6 Ð Typical Top View 19EX Shown Fig. 7 Ð Typical Side View 19EX ShownFig. 8 Ð Typical Motor End View 19EX Shown SERVICE CLEARANCES Fig. 9 Ð Typical DimensionsDIMENSIONS NOZZLE SIZESTable 2 Ð Refrigerant Charge Table 3 Ð Additional Cooler Weights Table 4 Ð Additional Condenser WeightsTable 5 Ð Auxiliary Connection Sizes Table 8 Ð Compressor Weights Table 6 Ð Total 19EX Motor Weights 60 HzTable 7 Ð Total 19EX Motor Weights 50 Hz Table 9 Ð Total 17EX Drive Component WeightsTable 10A Ð 17EX Motors Ð Total Weight, Lbs English Table 10B Ð 17EX Motors Ð Total Weight, Kg SIInstall Machine Supports Table 11 Ð Marine Waterbox Cover WeightsTable 12 Ð NIH Waterbox Cover Weights Fig. 10 Ð Machine Contact Surfaces COOLER SIZES 31-33 ANDCOOLER SIZES COOLER SIZESSOLEPLATE ISOLATION Fig. 11 Ð Machine Vibration IsolationACCESSORY ISOLATION TYPICAL ISOLATIONConnect Piping Fig. 12 Ð Typical Nozzle PipingNOZZLE-IN-HEAD WATERBOXES FRAME 3 AND 5 MARINE WATERBOXESFig. 13 Ð Nozzle Arrangements FRAME 4 MARINE WATERBOXES Fig. 13 Ð Nozzle Arrangements contFig. 14 Ð Pumpout Unit Fig. 15 Ð Water Piping, Oil Cooler to Chilled Water Circuit Typical Fig. 16 Ð Typical 17/19EX Utility Vessel Relief Valve TeeTable 13 Ð Relief Valve Locations and Data Table 14 Ð Individual Component Ratings Indicates remote alarm contacts Options Wiring Required Power WiringRequired Control Wiring Notes on following pageI GENERAL Fig. 19 Ð Oil Pump Wiring 19EX SHOWN Fig. 20 Ð 17/19EX with Free-Standing StarterFig. 21 Ð Oil Heater and Control Power Wiring Fig. 22 Ð Carrier Comfort Network Communication Bus WiringInstall Field Insulation Table 15 Ð Insulation Requirements19EX CHILLERS Factory Wiring Field WiringField-supplied terminal strip must be located in the control center FRONT VIEW PLAN VIEWFig. 24 Ð Typical Insulation Area 19EX Shown INSTALLATION START-UP REQUEST CHECKLIST TESTING