Manuals / Carrier / Kitchen Appliance / Refrigerator

Carrier 19EX, 17 Ð Machine Vibration Isolation, Soleplate Isolation, Typical Isolation

Models: 17 19EX

1 32

Download 32 pages 19.33 Kb

Page 16

SOLEPLATE ISOLATION

SOLEPLATE ISOLATION

TYPICAL ISOLATION

ACCESSORY ISOLATION

SOLEPLATE DETAIL

SECTION A-A

NOTES:

1. Dimensions in ( ) are in millimeters.

2.Accessory soleplate package includes 4 soleplates, 16 jacking screws and leveling pads. Requires isolation package.

3.Jacking screws to be removed after grout has set.

4.Thickness of grout will vary, depending on the amount necessary to level chiller. Use only pre-mixed non-shrinking grout, Celcote HT-648 or Master Builders 636, 0 -11¤2(38.1) to 0 -21¤4(57) thick.

STANDARD ISOLATION

VIEW B-B

ISOLATION WITH ISOLATION PACKAGE ONLY

(STANDARD)

NOTE: Isolation package includes 4 shear ¯ex pads.

Fig. 11 Ð Machine Vibration Isolation

16

Image 16

Carrier 19EX, 17 Ð Machine Vibration Isolation, Soleplate Isolation, Typical Isolation, Accessory Isolation

Contents

Installation Instructions SAFETY CONSIDERATIONS17/19EX 50/60 Hz Centrifugal Liquid Chillers with HFC-134a CONTENTS INSTALLATION Receiving the MachineINTRODUCTION Job DataFig. 1 Ð Model Number Identication ARI Air Conditioning`U STAMP and Refrigeration19EX Fig. 2 Ð Typical 19EX InstallationLocal Interface Display Control Panel Fig. 3 Ð Typical 17EX Installation 17EX FRONT VIEW Fig. 4 Ð 17EX Machine Rigging Guide19EX FRONT VIEW Fig. 5 Ð 19EX Machine Rigging GuideFig. 6 Ð Typical Top View 19EX Shown Fig. 7 Ð Typical Side View 19EX ShownFig. 8 Ð Typical Motor End View 19EX Shown Fig. 9 Ð Typical Dimensions DIMENSIONSSERVICE CLEARANCES NOZZLE SIZESTable 2 Ð Refrigerant Charge Table 4 Ð Additional Condenser Weights Table 3 Ð Additional Cooler WeightsTable 5 Ð Auxiliary Connection Sizes Table 6 Ð Total 19EX Motor Weights 60 Hz Table 7 Ð Total 19EX Motor Weights 50 HzTable 8 Ð Compressor Weights Table 9 Ð Total 17EX Drive Component WeightsTable 10A Ð 17EX Motors Ð Total Weight, Lbs English Table 10B Ð 17EX Motors Ð Total Weight, Kg SITable 11 Ð Marine Waterbox Cover Weights Install Machine SupportsTable 12 Ð NIH Waterbox Cover Weights COOLER SIZES 31-33 AND COOLER SIZESFig. 10 Ð Machine Contact Surfaces COOLER SIZESFig. 11 Ð Machine Vibration Isolation ACCESSORY ISOLATIONSOLEPLATE ISOLATION TYPICAL ISOLATIONConnect Piping Fig. 12 Ð Typical Nozzle PipingFRAME 3 AND 5 MARINE WATERBOXES NOZZLE-IN-HEAD WATERBOXESFig. 13 Ð Nozzle Arrangements Fig. 13 Ð Nozzle Arrangements cont FRAME 4 MARINE WATERBOXESFig. 14 Ð Pumpout Unit Fig. 15 Ð Water Piping, Oil Cooler to Chilled Water Circuit Typical Fig. 16 Ð Typical 17/19EX Utility Vessel Relief Valve TeeTable 13 Ð Relief Valve Locations and Data Table 14 Ð Individual Component Ratings Indicates remote alarm contacts Required Power Wiring Required Control WiringOptions Wiring Notes on following pageI GENERAL Fig. 19 Ð Oil Pump Wiring 19EX SHOWN Fig. 20 Ð 17/19EX with Free-Standing StarterFig. 21 Ð Oil Heater and Control Power Wiring Fig. 22 Ð Carrier Comfort Network Communication Bus WiringInstall Field Insulation Table 15 Ð Insulation RequirementsFactory Wiring Field Wiring 19EX CHILLERSField-supplied terminal strip must be located in the control center PLAN VIEW FRONT VIEWFig. 24 Ð Typical Insulation Area 19EX Shown INSTALLATION START-UP REQUEST CHECKLIST TESTING