Manuals / Carrier / Kitchen Appliance / Refrigerator

Carrier 23 XL Ð Piping Flow Data Frame, Cooler and Condenser Nozzle Arrangements

Models: 23 XL

1 36

Download 36 pages 34.69 Kb

Page 21

Fig. 21 Ð Piping Flow Data (Frame 4)

Cooler and Condenser Nozzle Arrangements

NOZZLE ARRANGEMENT CODES

		Cooler				Condenser
Pass	In		Out	Code	Pass	In	Out	Code
1	8		5	A	1	11	2	P
	5		8	B		2	11	Q

2	7		9	C	2	10	12	R
	4		6	D		1	3	S

3	7		6	E	3	10	3	T
	4		9	F		1	12	U

Waterbox Nozzle Sizes

		NOMINAL PIPE	ACTUAL PIPE
FRAME	PASS	SIZE (in.)	ID (in.)
		Cooler and Condenser	Cooler and Condenser
4*	1	10	10.020
4*	2	8	7.981
	3	6	6.065

*Frame 4 waterboxes are factory fabricated with bolt-on covers.

Fig. 21 Ð Piping Flow Data (Frame 4)

21

Image 21

Carrier 23 XL Ð Piping Flow Data Frame, Cooler and Condenser Nozzle Arrangements, Waterbox Nozzle Sizes

Contents

Installation Instructions SAFETY CONSIDERATIONS23XL 50/60 Hz Hermetic Screw Liquid Chillers With HCFC-22and HFC-134aINSTALLATION Receiving the Machine CONTENTSINSTALLATION START-UPREQUEST INTRODUCTIONREAR VIEW FRONT VIEWRigging the Machine Ð The 23XL can be rigged as an entire assembly. It also has ¯anged connections that allow the compressor, cooler, condenser, and oil separator sections to be separated to fulll specic installation requirements Suggested ``I Beam Spreader Bar Fig. 5 Ð Machine Rigging Guide Frame 4 Machines Suggested ``I Beam Spreader Bar²23-22 Fig. 6 Ð 23XL Dimensions Frame 1 and 2 MachinesFig. 7 Ð 23XL Dimensions Frame 4 Machines Table 2 Ð 23XL Component Weights Table 1 Ð 23XL Compressor WeightsTable 3 Ð 23XL Motor Weights Table 4 Ð 23XL Heat Exchanger WeightsTable 6 Ð 23XL Machine Rigging Weights 2.Disconnect and/or cut the following lines Refer to Fig. 10 unless otherwise specied Fig. 9 Ð 23XL Top View Frame 1 and 2 Machines Fig. 10 Ð 23XL Top View Frame 4 Machines Frame 4 Machines Fig. 11 Ð Motor Cooling Drain SectionFig. 12 Ð Oil Separator Section Frame 4 MachinesFig. 14 Ð 23XL Machine Footprint Frame 4 Machine Install Machine SupportsFig. 15 Ð Standard Isolation Fig. 16 Ð Accessory IsolationFig. 18 Ð Typical Low Prole Isolation Assembly Field Supplied and InstalledConnect Piping Fig. 19 Ð Typical Nozzle Piping Cooler and Condenser Nozzle Arrangements Waterbox Nozzle SizesFig. 20 Ð Piping Flow Data Frame 1 and Fig. 21 Ð Piping Flow Data Frame Cooler and Condenser Nozzle ArrangementsWaterbox Nozzle Sizes RATED DRY WEIGHT AND REFRIGERANT CAPACITY DIMENSIONSField Supplied and Installed Piping Factory Supplied and Installed PipingLEGEND Hidden Piping Factory Supplied and Installed Piping LEGEND Field Supplied and Installed PipingFig. 25 Ð Pumpout Unit Fig. 26 Ð Typical 23XL Relief Valve TreeTable 7 Ð Relief Device Locations Connect only 24 v wiring to the control center LEGEND 1Ð Chilled Water Pump Starter LEGEND 1Ð Chilled Water Pump Starter Fig. 30 Ð Carrier Comfort Network Communication Bus WiringInstall Field Insulation 23XL CHILLER LEGEND Factory Wiring Field Wiring23XL CHILLER 23XL CHILLERPage Page Copyright 1994 Carrier Corporation INSTALLATION START-UPREQUEST CHECKLIST TESTING