Manuals / Carrier / Kitchen Appliance / Refrigerator

Carrier 23 XL installation instructions Front View, Rear View

Models: 23 XL

1 36

Download 36 pages 34.69 Kb

Page 3

FRONT VIEW

FRONT VIEW

1 Ð Power Panel

2 Ð Local Interface Display (LID) Control Center

3 Ð ASME Nameplate, Cooler

4 Ð Cooler Refrigerant Isolation Valve

5 Ð ASME Nameplate, Economizer (Hidden)

6 Ð Service Valve

7 Ð Take-Apart Rabbet Fit Connector (Lower)

8 Ð Cooler Temperature Sensor

9 Ð ASME Nameplate, Condenser

10 Ð Typical Waterbox Drain Port

11 Ð Cooler Supply/Return End

Waterbox Cover

12 Ð Condenser Supply/Return End

Waterbox Cover

13 Ð Compressor Nameplate (Hidden)

REAR VIEW

14 Ð Oil Separator

15 Ð ASME Nameplate, Muffler (Hidden)

16 Ð ASME Nameplate, Oil Separator

17 Ð Cooler Relief Valves (Hidden)

18 Ð Oil Sump Filter Assembly

19 Ð Oil Charging Valve

20 Ð Vessel Separation Feet

21 Ð Float Chamber

22 Ð Condenser Isolation Valve (Option or Accessory)

23 Ð Refrigerant Charging Valve

24 Ð Condenser

25 Ð Condenser Relief Valves (Hidden)

26 Ð Take-Apart Rabbet Fit Connector (Upper)

27 Ð Unit Mounted Starter (Option)

28 Ð Machine Identi®cation Nameplate

Fig. 2 Ð Typical 23XL Installation (Frame 1 and 2 Machines)

3

Image 3

Carrier 23 XL installation instructions Front View, Rear View

Contents

With HCFC-22and HFC-134a SAFETY CONSIDERATIONSInstallation Instructions 23XL 50/60 Hz Hermetic Screw Liquid ChillersINTRODUCTION CONTENTSINSTALLATION Receiving the Machine INSTALLATION START-UPREQUESTREAR VIEW FRONT VIEWRigging the Machine Ð The 23XL can be rigged as an entire assembly. It also has ¯anged connections that allow the compressor, cooler, condenser, and oil separator sections to be separated to fulll specic installation requirements Suggested ``I Beam Spreader Bar Fig. 5 Ð Machine Rigging Guide Frame 4 Machines Suggested ``I Beam Spreader Bar²23-22 Fig. 6 Ð 23XL Dimensions Frame 1 and 2 MachinesFig. 7 Ð 23XL Dimensions Frame 4 Machines Table 4 Ð 23XL Heat Exchanger Weights Table 1 Ð 23XL Compressor WeightsTable 2 Ð 23XL Component Weights Table 3 Ð 23XL Motor WeightsTable 6 Ð 23XL Machine Rigging Weights 2.Disconnect and/or cut the following lines Refer to Fig. 10 unless otherwise specied Fig. 9 Ð 23XL Top View Frame 1 and 2 Machines Fig. 10 Ð 23XL Top View Frame 4 Machines Frame 4 Machines Fig. 11 Ð Motor Cooling Drain SectionFrame 4 Machines Fig. 12 Ð Oil Separator SectionFig. 14 Ð 23XL Machine Footprint Frame 4 Machine Install Machine SupportsFig. 15 Ð Standard Isolation Fig. 16 Ð Accessory IsolationFig. 18 Ð Typical Low Prole Isolation Assembly Field Supplied and InstalledConnect Piping Fig. 19 Ð Typical Nozzle Piping Cooler and Condenser Nozzle Arrangements Waterbox Nozzle SizesFig. 20 Ð Piping Flow Data Frame 1 and Fig. 21 Ð Piping Flow Data Frame Cooler and Condenser Nozzle ArrangementsWaterbox Nozzle Sizes RATED DRY WEIGHT AND REFRIGERANT CAPACITY DIMENSIONSField Supplied and Installed Piping Factory Supplied and Installed PipingLEGEND Hidden Piping Factory Supplied and Installed Piping LEGEND Field Supplied and Installed PipingFig. 25 Ð Pumpout Unit Fig. 26 Ð Typical 23XL Relief Valve TreeTable 7 Ð Relief Device Locations Connect only 24 v wiring to the control center LEGEND 1Ð Chilled Water Pump Starter LEGEND 1Ð Chilled Water Pump Starter Fig. 30 Ð Carrier Comfort Network Communication Bus WiringInstall Field Insulation 23XL CHILLER LEGEND Factory Wiring Field Wiring23XL CHILLER 23XL CHILLERPage Page Copyright 1994 Carrier Corporation INSTALLATION START-UPREQUEST CHECKLIST TESTING