Manuals / Carrier / Kitchen Appliance / Refrigerator

Carrier 23 XL Suggested ``I Beam Spreader Bar², Ð Machine Rigging Guide Frame 4 Machines

Models: 23 XL

1 36

Download 36 pages 34.69 Kb

Page 6

Suggested ``I'' Beam Spreader Bar²

NOTES:

1.Each chain must be capable of supporting the entire weight of the machine. Maxi- mum weight of machine is 22,300 lbs (10,116 Kg).

2.Chain lengths shown are typical for 15 ft (4572 mm) lifting height. Some minor ad- justment may be required.

3.[ ] indicates millimeters.

		CENTER OF GRAVITY Ð						MAXIMUM WEIGHT*
		APPROXIMATE DIMENSIONS						MAXIMUM WEIGHT*
	HEAT EXCHANGER	APPROXIMATE DIMENSIONS
	HEAT EXCHANGER		A			B
	SIZE		A			B
	SIZE	(Length)			(Width)			lb	kg
		(Length)			(Width)			lb	kg
		ft-in.		mm	ft-in.		mm
	40, 41, 42, or 43	6-4		1930	2-8		813	22,300	10,116

*Includes marine waterboxes and refrigerant charge.

Suggested ``I'' Beam Spreader Bar²

	OPTIONS	ENGLISH	SI
	OPTIONS	in. x lb/ft	cm x N/m
		in. x lb/ft	cm x N/m
	1	S12 x 31.8	S30 x 464
	2	S10 x 35	S25.4 x 511
	3	W12 x 22	W30 x 321
	4	W10 x 25	W25.4 x 365

²Carrier recommends that ``I'' beam spreader bars be ®eld supplied and installed.

Fig. 5 Ð Machine Rigging Guide

(Frame 4 Machines)

6

Image 6

Carrier 23 XL installation instructions Suggested ``I Beam Spreader Bar², Ð Machine Rigging Guide Frame 4 Machines

Contents

23XL 50/60 Hz Hermetic Screw Liquid Chillers SAFETY CONSIDERATIONSInstallation Instructions With HCFC-22and HFC-134aINSTALLATION START-UPREQUEST CONTENTSINSTALLATION Receiving the Machine INTRODUCTIONFRONT VIEW REAR VIEWRigging the Machine Ð The 23XL can be rigged as an entire assembly. It also has ¯anged connections that allow the compressor, cooler, condenser, and oil separator sections to be separated to fulll specic installation requirements Suggested ``I Beam Spreader Bar Suggested ``I Beam Spreader Bar² Fig. 5 Ð Machine Rigging Guide Frame 4 MachinesFig. 6 Ð 23XL Dimensions Frame 1 and 2 Machines 23-22Fig. 7 Ð 23XL Dimensions Frame 4 Machines Table 3 Ð 23XL Motor Weights Table 1 Ð 23XL Compressor WeightsTable 2 Ð 23XL Component Weights Table 4 Ð 23XL Heat Exchanger WeightsTable 6 Ð 23XL Machine Rigging Weights 2.Disconnect and/or cut the following lines Refer to Fig. 10 unless otherwise specied Fig. 9 Ð 23XL Top View Frame 1 and 2 Machines Fig. 10 Ð 23XL Top View Frame 4 Machines Fig. 12 Ð Oil Separator Section Fig. 11 Ð Motor Cooling Drain SectionFrame 4 Machines Frame 4 MachinesInstall Machine Supports Fig. 14 Ð 23XL Machine Footprint Frame 4 MachineFig. 16 Ð Accessory Isolation Fig. 15 Ð Standard IsolationFig. 18 Ð Typical Low Prole Isolation Assembly Field Supplied and InstalledConnect Piping Fig. 19 Ð Typical Nozzle Piping Cooler and Condenser Nozzle Arrangements Waterbox Nozzle SizesFig. 20 Ð Piping Flow Data Frame 1 and Fig. 21 Ð Piping Flow Data Frame Cooler and Condenser Nozzle ArrangementsWaterbox Nozzle Sizes DIMENSIONS RATED DRY WEIGHT AND REFRIGERANT CAPACITYField Supplied and Installed Piping Factory Supplied and Installed PipingLEGEND Hidden Piping LEGEND Field Supplied and Installed Piping Factory Supplied and Installed PipingFig. 25 Ð Pumpout Unit Fig. 26 Ð Typical 23XL Relief Valve TreeTable 7 Ð Relief Device Locations Connect only 24 v wiring to the control center LEGEND 1Ð Chilled Water Pump Starter LEGEND 1Ð Chilled Water Pump Starter Communication Bus Wiring Fig. 30 Ð Carrier Comfort NetworkInstall Field Insulation 23XL CHILLER LEGEND Factory Wiring Field Wiring23XL CHILLER 23XL CHILLERPage Page Copyright 1994 Carrier Corporation INSTALLATION START-UPREQUEST CHECKLIST TESTING