4.5.6.3 - Manual tests
This function allows the user to test the outputs individually, if the machine is completely shut down (LOFF). To carry out a manual test use the arrow keys to access the output to be tested and press the Enter key (longer than 2 seconds) to activate the modification mode. The password is automatically requested, if it has not previously been verified. The Outputs/Test LED on the user interface begins to flash. Enter the desired test value and again press Enter to start the test. 'TESt' is displayed on the 4- digit display alternately with the value tested. The Outputs/Test LED stops flashing. Press the Enter key or an arrow key to stop the test.
4.5.7 - Description of the Configuration menu
4.5.7.1- General
This menu can be used to display and modify all configura- tions: Factory, Service and User. Only the User Configuration can be modified by the
The menus User 1 [USEr 1] and User 2 [USEr 2] are pass-
4.5.7.2 - Password
A password must be entered in order to access the test function or to modify a configuration. It is automatically requested, if necessary: 'EntEr PASS' is displayed on the
This value can be modified through the Service configuration. The password can be entered if the unit is fully stopped, other- wise 'ACCES dEniEd' (access denied) will be displayed on the
ITEM | USER 1 | USER 2 | DATE | SCHEDULE 1 | SCHEDULE 2 | HOLIDAYS | BROADCAST |
| [USER1] | [USER2]* | [dAtE]* | [ScHEduLE 1MEnu]* | [ScHEduLE 2 MEnu]* | [HOLidAy MEnu]* | [BrodCASt]* |
0 | Return to previous menu | Return to previous | Return to previous | Return to previous menu | Return to previous | Return to previous menu | Return to previous menu |
|
| menu* | menu |
| menu |
|
|
1 | Circuit selection | Periodic pump start- | Hour* | Broadcast acknowledger | |||
|
| up* |
| Period 1 [PErIod 1] | Period 1 [PErIod 1] | Holidays 1 [HOLidAy 1] | selection |
2 | Circuit capacity increase | Night mode - start | Day of the week* | Broadcast activation | |||
| sequence | hour* |
| Period 2 [PErIod 2] | Period 2 [PErIod 2] | Holidays 2 [HOLidAy 2] |
|
3 | Ramp selection* | Night mode - end | Day and month* | Outdoor temperature | |||
|
| hour* |
| Period 3 [PErIod 3] | Period 3 [PErIod 3] | Holidays 3 [HOLidAy 3] | broadcast bus |
4 | Night mode - demand | Year* | Outdoor temperature | ||||
|
| limit in % |
| Period 4 [PErIod 4] | Period 4 [PErIod 4] | Holidays 4 [HOLidAy 4] | broadcast element |
5 | Water pump selection | Number clock 1* | - | Start month daylight | |||
|
|
|
| Period 5 [PErIod 5] | Period 5 [PErIod 5] | Holidays 5 [HOLidAy 5] | saving time |
6 | Water pump changover | Number clock 2* | - | Start day daylight saving | |||
| delay* |
|
| Period 6 [PErIod 6] | Period 6 [PErIod 6] | Holidays 6 [HOLidAy 6] | time |
7 | Automatic reset | CCN address * | - | Start hour daylight saving | |||
| selection* |
|
| Period 7 [PErIod 7] | Period 7 [PErIod 7] | Holidays 7 [HOLidAy 7] | time |
8 | Demand limit selection | CCN bus* | - | Minutes to add | |||
|
|
|
| Period 8 [PErIod 8] | Period 8 [PErIod 8] | Holidays 8 [HOLidAy 8] |
|
9 | Voltage corresponding to | - | - | - | - | End month daylight saving | |
| 100% of demand limit |
|
|
|
| Holidays 9 [HOLidAy 9] | time |
10 | Voltage corresponding to | - | - | - | - | End day daylight saving | |
| 0% of demand limit |
|
|
|
| Holidays 10 [HOLidAy 10] | time |
11 | Extended display | - | - | - | - | End hour daylight saving | |
| selection |
|
|
|
| Holidays 11 [HOLidAy 11] | time |
12 | Password for all user | - | - | - | - | Minutes to subtract | |
| configurations |
|
|
|
| Holidays 12 [HOLidAy 12] |
|
13 | Software version number | - | - | - | - | - | |
|
|
|
|
|
| Holidays 13 [HOLidAy 13] |
|
14 | - | - | - | - | - | - | |
|
|
|
|
|
| Holidays 14 [HOLidAy 14] |
|
15 | - | - | - | - | - | - | |
|
|
|
|
|
| Holidays 15 [HOLidAy 15] |
|
16 | - | - | - | - | - | - | |
|
|
|
|
|
| Holidays 16 [HOLidAy 16] |
|
Legend:
*: only displayed if configuration requires.
20