Applying Effects to a Sound

2. If you want, use the R-17 (t, y) buttons to

 

 

8. Use the mixer to adjust the chorus send of the

 

move the thick brackets (%) to the “DSP

 

 

 

part to which you want to apply chorus.

Disable”setting, and then use the R-14 (–, +)

 

 

 

• You can use “Cho.Send” (Part Chorus Send, page

buttons to change the setting to “on”.

 

 

 

 

E-43) to adjust how chorus is applied to the tone of

•

For more information about this setting, see the

 

 

 

 

each keyboard or Auto Accompaniment part. The initial

 

 

 

 

default setting is 0 for the chorus send of all parts, so

 

“Important!” note below.

 

 

 

 

 

 

 

 

 

change the settings to a chorus send value greater than

•

If you turning on the “DSP Disable” setting, you should

 

 

 

 

 

 

 

 

0 for all parts to which you want to apply the chorus

 

skip steps 3 and 4 below.

 

 

 

 

 

 

 

 

 

effect. For details, see “Using the Mixer” (page E-38).

3. Use the R-17 (t, y) buttons to move the thick

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

brackets (%) to the “Chorus/DSP” setting.

 

 

 

 

 

 

 

 

 

 

 

 

 

• Selecting a tone with DSP causes the “Chorus/DSP”

4. Use the R-14 (–, +) buttons to select “Chorus”.

 

 

 

 

 

setting to change automatically to the “DSP” (DSP

•

This enters the chorus effect mode, which enables the

 

 

 

effect mode), so the chorus effect will not be available.

 

use of the chorus effect.

 

 

 

If you want the chorus effect always to be available,

5. Use the R-17 (t, y) buttons to move the thick

 

 

 

change the “DSP Disable” setting to “on”. This will

 

 

 

keep the Digital Keyboard in the chorus effect mode.

brackets (%) to the “Chorus” setting.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• A pointer indicator is displayed next to CHORUS when

 

 

 

 

 

“Chorus” is selected for the “Chorus/DSP” setting. The

 

 

 

 

 

pointer indicator is not displayed next to CHORUS when

 

 

 

 

 

“oFF” is selected for the chorus type or when “DSP” is

 

 

 

 

 

selected for the “Chorus/DSP” setting.

 

 

 

 

• Selecting “Chorus” for the “Chorus/DSP” setting will cause

 

 

 

 

 

the “DSP Line” (Part DSP Line, page E-43) setting for all

 

 

 

 

 

parts to be changed to “oFF”.

6. Use the dial or R-14 (–, +) buttons to select the

 

 

 

To use a DSP

 

 

 

 

 

1. While holding down the R-13 (FUNCTION)

chorus type you want to use.

 

 

•

Refer to the separate “Appendix” for information about

 

 

 

button, press the C-7 (EFFECT) button to

 

supported chorus types.

 

 

 

display the effect setting screen.

7. Press the C-7 (EFFECT) button or the R-15

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(EXIT) button.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

•

This exits the effect setting screen.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Check to make sure that the “DSP Disable” setting is

 

 

 

 

 

 

 

 

 

 

 

“oFF”. If it is “on”, change it to “oFF”.

 

 

 

 

2. Use the R-17 (t, y) buttons to move the thick

 

 

 

 

 

brackets (%) to “Chorus/DSP”.

 

 

 

 

3. Use the R-14 (–, +) buttons to select “DSP”.

 

 

 

 

 

• This enters the DSP effect mode, which enables the

 

 

 

 

 

 

use of the DSP effect.

 

 

 

 

 

 

 

 

 

 

 

 

 

E-34