Casio AT-3, AT-5 manual 75

					Using the Song Sequencer
6. Use the R-17 (u, i) buttons to move the
					Using Panel Record to Rewrite
	cursor, use the dial or the R-14 (–, +) buttons to
					Song Header Settings
	change the value at the cursor position, and
	then press the R-16 (ENTER) button.		The header of each song contains “header settings”, which
	• If you have already specified a range using the locator		are settings that were in effect on the Digital Keyboard when
	screen (page E-75), you can copy that range to this		recording was performed. You can use a “panel record”
	screen by holding down the L-13 (REPEAT) button.		operation to rewrite a song’s header settings with the Digital
			Keyboard’s current setup.
			The following items are header settings that can be rewritten
			using the panel record operation.
			•		Rhythm selection
			• Tempo setting
			•		Scale setting
			•		The mixer settings below
					– All part parameters from A04 through A07 and B01
					through B16 (Excluding part on/off)
					– Part parameters from A09 through A16: part on/off,
					coarse tune, fine tune, scale enable, DSP line
	Recording start point	Recording end point
					– DSP parameters: volume, pan, reverb send
7. After specifying the recording start point and			•		Effect settings
			• Accomp volume
	end point, press the L-17 (START/STOP) button.		• UPPER 1 part tone, UPPER 2 part tone, and LOWER part
	• This starts punch-in playback. You can perform fast				tone selections
	forward and fast backward operations during punch-in			To perform a panel record operation
	playback using the operations described in step 6
	under “To start re-recording from a particular location		1. Press the C-5 (SONG SEQUENCER) button to
	during playback (Manual Punch-in)” (page E-71).
	• You can start punch-in playback from one measure				enter the song sequencer mode.
	prior to the current recording start point by pressing the
	L-13 (REPEAT) button which causes the ?
	indicator to appear on the display.

8.When playback reaches the re-record point you specified, start playing something on the

keyboard.		2. Use the dial or R-14 (–, +) buttons to select a
•	Punch-in recording will start automatically when
	playback reaches the record start point you specified.	song area number.
	The C-6 (RECORD) button will light when recording	3. Configure panel settings so they reflect the
	starts.
•	Recording stops and punch-in recording is exited	settings you want to write as the header
	automatically when the record end point you specified	settings.
	is reached. At this time the C-6 (RECORD) button will
		• You can configure the following settings: mixer settings,
	become unlit.
		tempo, system track rhythm, track tone selection, etc.
•	If you want to stop recording before the record end
		• To change the system track UPPER 1, UPPER 2, and
	point you specified is reached, press the L-17 (START/
		LOWER part tones or mixer settings, use the mixer to
	STOP) button. Any previously recorded data in the
		change the settings of parts A05 (UPPER 1), A06
	track that comes after the point you stopped punch-in
		(UPPER 2), and A07 (LOWER).
	recording will remain in the track.
•	When “EOT” (End of Track) is selected for the	4. After all of the panels settings are the way you
	recording start point, the start point for punch-in
		want, hold the R-13 (FUNCTION) button as you
	recording is the end of the track.
		press the C-17 (MENU) button.
•	When “OFF” is selected for the recording end point,
	punch-in recording will not stop automatically because	• This displays the song sequencer menu.
	no end point is specified. To stop punch-in recording in
	this case, press the L-17 (START/STOP) button.

E-73