Using the Mixer

• When you move the thick brackets (%) to one of the

Mixer Operationsetting values of a part parameter, all of the part parameter values of the Group (A or B) to which the

To change mixer parameters

part belongs are indicated by level meter black boxes.

1.Press the C-7 (MIXER) button.

 

•

This causes the mixer screen to appear.

4. Use the dial or R-14 (–, +) buttons to change the

 

 

 

 

 

 

 

 

Currently selected setting

 

setting value.

(MASTER, DSP, MIC/INST, or A01 to A16/B01 to B16)

 

•

Pressing the R-14(–, +) buttons at the same time

 

 

 

 

 

 

 

 

 

 

returns a parameter to its initial default setting.

 

 

 

 

 

 

 

 

 

•

While the “Part” (part on/off) setting of a part parameter

 

 

 

 

 

 

 

 

 

 

is being configured, pressing both of the R-14(–, +)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

buttons at the same time will change the setting to “Sol”

 

 

 

 

 

 

 

 

 

 

(Solo). For details, see “Part Parameters” (page E-43).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5. Repeat steps 2 through 4 as required to

 

 

 

 

 

 

 

 

 

configure other parameters.

Parameter/Setting value

 

6. To exit the mixer, press the C-7 (MIXER) button

 

 

 

 

 

 

 

 

 

 

 

 

 

Currently selected setting part

 

 

 

 

 

 

or the R-15 (EXIT) button.

 

 

(when currently selected setting is A01 to A16/B01 to B16)

 

 

 

 

 

 

 

 

 

 

•

This exits the mixer screen.

2. Use the R-17 (u, i) buttons to select the

 

 

 

 

 

 

 

 

 

mixer parameter you want to change.

 

 

 

 

 

 

 

 

 

• While master (MASTER), effect (DSP) or microphone input

 

•

You can select master (MASTER), effect (DSP),

 

(MIC/INST) is selected in step 2 above for setting, you also

 

 

microphone input (MIC/INST), or a part (A01 through

 

can perform normal keyboard play (play using layer, split,

 

 

A16, B01 through B16). The currently selected setting

 

and Auto Accompaniment).

 

 

is shown in the line two of the display.

• While an individual part (A01 through A16, B01 through

 

•

While a part is selected, you can toggle between Group

 

B16) is selected in step 2 above for setting, pressing a

 

 

A and Group B by pressing both of the R-17 (u, i)

 

keyboard key will sound only notes of the selected part. All

 

 

buttons at the same time.

 

other types of performance operations (layer, split, Auto

 

 

 

 

 

 

 

 

 

Accompaniment, etc.) are disabled.

3.Use the R-17 (t, y) buttons to move the thick brackets (%) to the parameter you want to change.

•The parameters that can be configured depend on the currently selected setting. For details, refer to the sections shown in the table below.

When this setting is

These parameters can be

selected:

configured:

MASTER

MASTER parameters

 

(page E-41)

 

 

MIC/INST

MIC/INST parameters

 

(page E-42)

 

 

DSP

DSP parameters (page E-41)

 

 

A01 to A16/B01 to B16

Part parameters (page E-43)

 

 

E-39