Chamberlain WD962KLD Readandfollowallwarningsand Instructions, Using Your Garage Door Opener

OPERATION

iiVtPORTANT SAFETY INSTRUCTnONS

To reduce the risk of SEVERE iNJURY or DEATH:

I. READANDFOLLOWALLWARNINGSAND INSTRUCTIONS.

2ALWAYSkeepremotecontrols out of reachof children NEVERpermit childrento operateor playwith garage control consolepush buttons or remotecontrols

3.ONLYactivategaragedoor when it can beseen clearly,it is properly adjusted,andthere are no obstructionsto door travel.

4ALWAYSkeepgaragedoor in sight until completelyclosed

NO ONESHOULDCROSSTHEPATHOFTHEMOVING DOOR.

5..NOONESHOULDGOUNDERA STOPPED,PARTIALLY OPENEDDOOR

6.if possible, useemergencyreleasehandleto disengage trolley ONLYwhengaragedoor is CLOSEDWeakor broken springs or unbalanceddoor could result in an opendoor falling rapidlyand/or unexpectedly_

7NEVERuseemergencyreleasehandleunlessgarage doorway is clear of personsand obstructions..

8.NEVERusehandleto pull garagedoor openor closed. If ropeknot becomesuntied,you could fall

Using Your Garage Door Opener

Your Security+ _ opener and hand-held remote control have been factory-set to a matching code which changes with each use, randomly accessing over 100 billion new codes.. Your opener will operate with up to eight Security,__ remote controls and one Security'l-_ Keyless Entry System. If you purchase a new remote, or if you wish to deactivate any remote, follow the instructions in the Programming section..

Activate your opener with any of the following:

•The hand-hold Remote Control: Hold the large push button down until the door starts to move..

•The wall-mounted control console: Hold the push button or bar down until the door starts to move.

•The Keyless Entry (see Accessories):' If provided with

your garage door opener, it must be programmed before use..See Programming.

When the opener is activated (with the safety reversing sensor correctly installed and aligned)

1.If open, the door will close.. If closed, it wilt open.

2If closing, the door will reverse..

3.If opening, the door will stop°

4..If the door has been stopped in a partially open position, it will close.

5.If obstructed while closing, the door will reverse.. If the obstruction interrupts the sensor beam, the opener lights will blink for five seconds.

9tf onecontrol (force or travellimits) is adjusted,the other control mayalso needadjustment..

10..After ANYadjustmentsaremade,the safetyreversal system MUSTbetested..

11.SafetyreversalsystemMUSTbetested everymonth Garagedoor MUSTreverseon contactwith 1-I/2" high (3.8 cm) object (ora 2x4 laidfiat) on the floor

12ALWAYSKEEPGARAGEDOORPROPERLYBALANCED

(see page3). Animproperiy balanceddoor maynot reversewhen requiredand could result in SEVEREINJURY or DEATH.

13.ALL repairsto cables,spring assembliesand other hardware,ALLof whichareunder EXTREMEtension, MUSTbe madeby a traineddoor systemstechnician.

I4 To avoid SERIOUSPERSONALINJURYor DEATHfrom electrocution,disconnectALLelectric andbattery power BEFOREperformingANYserviceor maintenance.

SAVETHESEnNSTRUCTIONS.

6_If obstructed while opening, the door witl stop.

7.If fully open, the door will not close when the beam Es broken.. The sensor has no effect in the opening cycle,

If the sensor is not installed, or is misaligned, the door won'tclose from a hand-hefd remote. However, you can close the door with the control console, the Outside

Keylock, or Keytess Entry, if.you activate them until down travel is complete_ tf you release them too soon, the door will reverse..

The opener lights wilt turn on under the following conditions: when the opener is initially plugged in; when power is restored after interruption;when the opener is activated..

They will turn off automatically after 4-1/2 minutes or provide constant light when the Light feature on the Control Console is activated. Bulb size is 100 watts maximum.

Security*_ light feature: Lights will also turn on when someone walks through the open garage door.. With a Motion Detecting Door Control Console, this feature may be turned off as follows: With the opener lights off, press and hold the light button for 10 seconds, until the light goes on, then off again.,To restore this feature, start with the opener lights on, then press and hold the light button for 10 seconds until the light goes off, then on again

31