Manuals / Chicago Electric / Power Tools / Welder

Chicago Electric 95424 Installing a Wire Spool, For use with a 7 Spool, For use with a 11 Spool

Models: 95629 95424

1 39

Download 39 pages 27.82 Kb

Page 13

ASSEMBLY INSTRUCTIONS (CONTINUED)

Installing a Wire Spool

Assembling the Wire Spool depends on whether you are using a 7” Spool or an 11” Spool.

For use with a 7” Spool:

1.

2.

Lift the Door (14A) of the Welder to expose

the Wire Drive Assembly.

Insert the Spool and the Pressing Cartridge onto the Threaded Shaft (11A). Making sure the Spool's Welding Wire unwinds from the bottom (clockwise).

3.

4.

When a slight force is needed to turn Spool,

tension is set.

Screw the Fixing Cover into the Threaded

Shaft (11A).

For use with a 11” Spool:

1.

2.

Lift the Door (14A) of the Welder to expose

the Wire Drive Assembly.

Insert the Spool′s Holder onto the

Threaded Shaft (11A).

	SKU 95424, 95629	For technical questions, please call 1-800-444-3353;	Page 13
		Troubleshooting section at end of manual.

Image 13

Chicago Electric 95424, 95629 manual Installing a Wire Spool, For use with a 7 Spool, For use with a 11 Spool

Contents

For technical questions or replacement parts, please call Assembly And Operation InstructionsContents Please Note SpecificationsSave this Manual Electrical Safety General Safety RulesWork Area Tool USE and Care Personal SafetySpecific Safety Rules ServiceIndustrial applications must follow Osha guidelines Page Welding Produces toxic fumes and gasses Inhalation HazardCylinders can explode when damaged Grounding SymbologyExtension Cords Unpacking Assembly InstructionsAttaching the Wheels Stationary MobileSee , above right See , above left For use with a 7 Spool Installing a Wire SpoolFor use with a 11 Spool Routing the Wire Figure B Exercise Extreme Caution Risk of Fire AND/OR Electric Shock Attaching the Ground Cable with Clamp Changing Wire SettingsAttaching the Electrode Cable Arc Welder Only See Figure FSee illustration, top right initial Setup Setting Polarity for Welding TypeSet for Electrode Negative Dcen for gasless flux core wire See illustration, bottom rightFigure G Installing a Gas CylinderOperating Instructions Other settings fall between these two rangesBefore You Begin Welding Understanding Duty Cycle Duration of UseVoltage Selector Knob 5C Setting Up the WeldArc Stick Welding Set Up for Model 95424 Only MIG Welding Set UpSee Figures K & J See Figure KFigure J MIG Weld Settings ChartStarting a weld arc for stick arc welding only Arc Stick Welding Set Up , for Model 95424 OnlySee Figure L MIG welding only When the Weld is CompletedNozzle Inspection, Cleaning, and Replacement MIG Only INSPECTION, MAINTENANCE, and CleaningContactTip Inspection, Cleaning, and Replacement MIG Only Or more for .030Tips .067 or more for .045TipsReplacing the Welding Torch Liner MIG Only WarrantyParts List a Parts Lists and DiagramsAssembly Diagrams Power Block #32A Assembly DiagramsFigure N Front Panel #23AFigure O Wire Drive Assembly #16AFigure P Gun SB 25 #20AControllerBlock BCN-4U MIG/Arc Welder 95424 Electrical SchematicMIG Dual Welder 95629 Electrical Schematic Page Welder does not function when switched on TroubleshootingWeak arc strength Welding arc not stableTroubleshooting Wire feeds, but arc does not ignite MIG welding onlyNozzle Plugged Wire feed motor does not run MIG welding onlyRegulator or cylinder valve closed Gas line blocked