Chapter 3 Configuring and Managing the IP Camera
Log Windows
Table | Log Messages |
|
|
|
| |||
|
|
|
|
|
| |||
| Message Name |
| Description that Appears in Log File | Explanation | Severity | |||
|
|
|
|
|
| |||
| CONFIG_SAVE_FAILED | Saving configuration to user <user> | A user attempt to save the IP camera | 3 |
| |||
|
|
|
|
| <IP address or hostname> failed. | configuration failed. |
|
|
|
|
|
|
|
| |||
| CONFIG_SAVED | Configuration saved by user <user> | The IP camera configuration was saved | 5 |
| |||
|
|
|
|
| <IP address or hostname>. | by a user. |
|
|
|
|
|
|
|
| |||
| CONFIG_UPLOAD_FAILED | Uploading configuration failed from | A user attempt to import the IP camera | 3 |
| |||
|
|
|
|
| user <user> <IP address or hostname>. | configuration failed. |
|
|
|
|
|
|
|
| |||
| CONFIG_UPLOADED | Configuration uploaded from user | The IP camera configuration was | 5 |
| |||
|
|
|
|
| <user> <IP address or hostname>. | imported by a user. |
|
|
|
|
|
|
|
| |||
| DEFAULTS_FAILED | Restoring factory defaults failed for | An attempt to reset the IP camera to its | 3 |
| |||
|
|
|
|
| user <user> <IP address or hostname>. | factory default configuration failed. |
|
|
|
|
|
|
|
| |||
| DEFAULTS_RESTORED | Factory defaults restored successfully | The IP camera was reset to its factory | 5 |
| |||
|
|
|
|
| by user <user> <IP address or | default configuration. |
|
|
|
|
|
|
| hostname>. |
|
|
|
|
|
|
|
|
| |||
| DEVICE_REBOOT_AUTO | Device rebooted. | The IP camera rebooted automatically. | 5 |
| |||
|
|
|
|
|
| |||
| DEVICE_REBOOT_MANUAL | Device was rebooted manually by user | The IP camera was rebooted by a user. | 5 |
| |||
|
|
|
|
| <user> <IP address or hostname>. |
|
|
|
|
|
|
|
|
|
| ||
| DHCP_LEASE |
| DHCP lease renewal was successful. | The IP camera renewed its DHCP | 6 |
| ||
|
|
|
|
|
| lease. |
|
|
|
|
|
|
|
| |||
| DSP_ENCODING_HALTED | The Codec/Sensor module’s DSP | The DSP of the IP camera codec/sensor | 2 |
| |||
|
|
|
|
| encoding was halted. Either the analog | module DSP stopped encoding. The |
|
|
|
|
|
|
| image signal from the sensor has been | analog image signal from the sensor |
|
|
|
|
|
|
| lost, or an internal encoding error has | may be lost or an internal encoding |
|
|
|
|
|
|
| occurred. | error may have occurred. |
|
|
|
|
|
|
|
| |||
| EMAIL_TRIGGERED | Event triggered: email sent to | An event occurred and | 5 |
| |||
|
|
|
|
| address>. | notification of the event was sent. |
|
|
|
|
|
|
|
|
| ||
| ETH_BER |
| Bit Error Rate (BER) exceeded | The bit error rate (BER) exceeded the | 4 |
| ||
|
|
|
|
| specified threshold of <threshold>. | specified threshold. |
|
|
|
|
|
|
|
| |||
| ETH_SIGNAL_DEGRADE | Ethernet signal degrading. | The IP camera detected a degrading | 4 |
| |||
|
|
|
|
|
| Ethernet signal. |
|
|
|
|
|
|
|
| |||
| FRAMES_DROPPED | Output frame rate does not match the | The IP camera is sending video at a | 3 |
| |||
|
|
|
|
| camera’s configured frame rate. | frame rate that does not match the |
|
|
|
|
|
|
|
| configured frame rate. |
|
|
|
|
|
|
|
| |||
| FW_UPGRADE_FAILED | Upgrading firmware failed from user | An attempt to upgrade the IP camera | 0 |
| |||
|
|
|
|
| <user> <IP address or hostname>. | firmware failed. |
|
|
|
|
|
|
|
| |||
| FW_UPGRADED | Firmware upgraded successfully from | The IP camera firmware was updated. | 5 |
| |||
|
|
|
|
| user <user> <IP address or hostname>. |
|
|
|
|
|
|
|
|
| |||
| HTTP_TRIGGERED | Event triggered: notification sent to | An event occurred and HTTP | 5 |
| |||
|
|
|
|
| HTTP server <IP address or | notification of the event was sent. |
|
|
|
|
|
|
| hostname>. |
|
|
|
|
|
|
|
|
| |||
| INPUT_ONE_CHANGED | Input port one changed to <high/low>. | Input port 1 on the IP camera changed | 5 |
| |||
|
|
|
|
|
| state. |
|
|
|
|
|
|
|
| |||
| INPUT_ONE_RESET | Input port one reset to <high/low>. | Input port 1 on the IP camera reset to | 5 |
| |||
|
|
|
|
|
| its default state. |
|
|
|
|
|
|
|
|
|
| |
|
|
| Cisco Video Surveillance 4300E and 4500E |
|
| |||
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|