Manuals / Cisco Systems / Computer Equipment / Switch

Cisco Systems N55M4Q manual Powering the Switch, Equipment That You Supply, Box Contents

Models: N55M4Q

1 36

Download 36 pages 49.44 Kb

Page 4

Equipment That You Supply

Chapter 2 Switch Installation

Powering the Switch

•Temperature around the unit does not exceed 113°F (45°C).

If the switch is installed in a closed environment or in a multirack assembly, the temperature around it might be greater than normal room temperature.

•Humidity around the switch must not exceed 95 percent.

•Altitude at the installation site must not be greater than 10,000 feet (3,049 meters).

•Do not place any items on the top of the switch.

•Do not wall-mount the switch with its front panel facing up. Following safety regulations, wall-mount the switch with its front panel facing down or to the side to prevent airflow restriction and to provide easier access to the cables.

•Clearance to the switch front and rear panels meets these conditions:

–You can easily read the front-panel LEDs.

–Access to ports is sufficient for unrestricted cabling.

–The AC power cord can reach from the AC power outlet to the connector on the switch rear panel.

•For 10/100 and 10/100/1000 fixed ports, cable lengths from the switch to connected devices are not more than 328 feet (100 meters).

•For cable lengths for small form-factor pluggable (SFP)-module connections, see the “SFP Module Connectors” section on page B-2and the module documentation.

Equipment That You Supply

You might need this equipment to install the switch:

•Number-2 Phillips screwdriver

•Drill with a #27 drill bit (0.144-inch [3.7 mm])

Box Contents

The switch getting started guide on Cisco.com describes the box contents. If any item is missing or damaged, contact your Cisco representative or reseller for support.

Powering the Switch

Before installing the switch in a rack, on a desk, a shelf, or a wall, you should power on the switch and verify that it passes POST.

Power the switch:

Catalyst 2960CPD-8PT-L and 2960CPD-8TT-L

•Connect a 10/100/1000 uplink port to a PoE or PoE+ switch, such as a Catalyst 3750-X. Or

•Plug the auxiliary power adapter cord into the switch AUX power connector and into an AC power outlet.

Catalyst 3560-C and 2960-C Switch Hardware Installation Guide

2-4	OL-23803-02

Image 4

Cisco Systems N55M4Q manual Powering the Switch, Equipment That You Supply, Box Contents

Contents

Preparing for Installation Preparing for Installation, page Verifying Switch Operation, pageMounting the Switch, page Installing a Cover for the Reset Button Optional, pageWarning Class 1 laser product. Statement Installation Guidelines Warning No user-serviceable parts inside. Do not open. StatementBox Contents Powering the SwitchEquipment That You Supply Verifying Switch Operation Mounting the SwitchOn a Desk or Shelf without Mounting Screws Desk, Shelf, or Wall with Mounting Screws With a Mounting TrayDesk, Shelf, or Wall with Mounting Screws On a Desk or Shelf without Mounting ScrewsDesk- or Shelf-Mounting Screw template 3 Desk or shelf Screws Under the Desk- or Shelf-Mounting Figure 2-3 Installing the Mounting Screws Under a Desk or Shelf Wall-Mounting 2-10Desk or shelf Slides on this way2-11 Step 3 Peel the adhesive strip off the bottom of the screw template2-12 Figure 2-6 Installing the Mounting Screws on the WallFigure 2-7 Installing the Switch on a Wall Chapter 2 Switch Installation Mounting the SwitchMounting Tray with Screws With a Mounting Tray2-13 Figure 2-9 Installing the Switch on the Mounting Tray 2-14ONSOLE 2-15 Mounting Tray with a MagnetFigure 2-10 Securing the Mounting Tray to the Switch Figure 2-11 Placing the Switch on the Mounting Tray 2-16Figure 2-12 Securing the Mounting Tray to the Switch 2-17 Figure 2-13 Wall-Mounting with a MagnetAttaching Brackets to the Switch Attaching Brackets to the Switch, pageMounting the Switch in a Rack, page In a RackMounting the Switch in a Rack 2-19Figure 2-16 Mounting the Switch in a Rack Figure 2-15 Attaching the 23-inch Brackets for Rack-MountingAttaching the DIN-Mount Tray to the Switch Attaching the DIN-Mount Tray to the Switch, pageMounting the Switch on a DIN Rail, page Removing the Switch from a DIN Rail, page2-21 Mounting the Switch on a DIN RailFigure 2-18 Securing the DIN-Mount Tray to the Switch 2-22 Figure 2-19 Mounting the Switch on a DIN Rail2-23 Removing the Switch from a DIN RailSwitch Removal Installing a Cover for the Reset Button Optional 2-24Figure 2-21 Reset Cover on the Catalyst 2960CPD-8PT-L Switch Figure 2-22 Reset Cover on the Catalyst 2960CG-8PC-S SwitchInstalling the Power Cord Retainer Optional 2-25Figure 2-24 Sliding the Retainer Through the Latch 2-26Figure 2-25 Locking the Retainer 2-27 Figure 2-26 Sleeve Around the Power CordFigure 2-27 Securing the Power Cord in the Retainer Chapter 2 Switch InstallationInstalling the Cable Guard Optional 2-282-29 Figure 2-29 Attaching the Cable Guard to the SwitchFigure 2-30 Pivoting the Cable Guard Upwards CatalystFigure 2-31 Attaching the Cables to the Switch 2-30Figure 2-32 Guiding the Cables through the Guard After Installing the Switch Installing SFP Modules2-31 Figure 2-33 Securing the Cable Guard to the Desk2-32 Removing SFP ModulesWarning Class 1 laser product. Statement Connecting Devices to the Ethernet Ports Connecting to the 10/100 and 10/100/1000 PortsConnecting to the 10/100 and 10/100/1000 Ports, page Connecting to the PoE Ports, pageConnecting to the PoE Ports DeviceCrossover Cable 2-34Where to Go Next 2-352-36 Chapter 2 Switch Installation Where to Go NextCatalyst 3560-C and 2960-C Switch Hardware Installation Guide OL-23803-02