Manuals / Cisco Systems / Computer Equipment / Network Router

Cisco Systems OL-6217-01 manual sup720# show mobility status, mobility ap

Models: OL-6217-01

1 38

Download 38 pages 11.63 Kb

Page 30

sup720# show mobility status

Cisco Structured Wireless-Aware Network (SWAN) Implementation Guide

Implementing the Cisco SWAN Framework

You should also navigate to the Catalyst 6500 Supervisor command-line interface and validate that the control communications between the WLSM and supervisor are correctly working. Enter this command to take a general look at the status:

show mobility status

Enter this command to show the slot location of the WLSM, the LCP status, tunnel information, registered access points, registered mobile nodes, and important information about the tunnels:

sup720# show mobility status

WLAN Module is located in Slot: 1 (HSRP State: Not Applicable)

LCP Communication status: up

MAC address used		for Proxy ARP: 0008.2034.7400
Number	of Wireless Tunnels: 4
Number	of Access	Points: 1
Number	of Mobile	Nodes: 3
Wireless Tunnel Bindings:
Src IP	Address	Wireless Network-ID	Trusted	Broadcast
---------------		-------------------	-------	---------

10.100.1.1	1	No	Yes
10.100.2.1	2	Yes	Yes
10.100.3.1	3	Yes	Yes
10.100.4.1	4	Yes	No

Enter the following command to show information about the registered access points:

show mobility ap

The IP addresses, MAC addresses, and appropriate network identifiers for the registered access points are shown:

sup720# show	mobility ap
AP IP Address AP Mac Address		Wireless Network-ID
---------------	-------------- -------------------
10.200.20.49	000b.fcfb.e836	4

Enter the following command to show information about registered client mobile nodes:

show mobility mn

The MN MAC address, MN IP address, the IP address of the MN's current access point, and the network identifier of the MN is shown:

sup720# show mobility		mn
MN Mac Address	MN IP	Address	AP IP Address	Wireless Network-ID
-------------- --------------- ---------------				-------------------
0004.e28b.2c28	172.16.4.3		10.200.20.49	4
00d0.59c8.60e1	172.16.4.2		10.200.20.49	4

Enter the following command to show information about a specific mobility group.

show mobility network <network-id>

Cisco Structured Wireless-Aware Network (SWAN) Implementation Guide

30	OL-6217-01

Image 30

Cisco Systems OL-6217-01 manual sup720# show mobility status, mobility ap

Contents

January Corporate HeadquartersCisco Structured Wireless-Aware Network SWAN Implementation Guide Cisco Systems, Inc 170 West Tasman Drive San Jose, CACisco Aironet 1400 Series Wireless Bridge Deployment Guide Turn the television or radio antenna until the interference stopsValidating the Configuration Validating the SetupManaging the Access Points with the CiscoWorks WLSE C O N T E N T SContents Book Title 78-xxxxx-xxAudience Cisco Structured Wireless-Aware Network SWAN Implementation GuideAcroymns and Terms TermDefinition Cisco SWAN Framework Overview TermDefinition Figure 1 Cisco SWAN Layers Figure 2 Cisco SWAN Logical View Figure 3 shows the access point-based WDS solution CISCO SWAN Framework Components Hardware Components Infrastructure Access PointsSoftware Components WLCCPCisco Wireless LAN Solution Engine CiscoWorks WLSE Implementing the Cisco SWAN FrameworkWLAN Client Devices Common Tasks Define each WDS-host as a network access server NAS Adding Username and Password Credentials Figure 6 CiscoSecure ACS NAS SetupFigure 7 CiscoSecure ACS User Setup Figure 8 CiscoSecure ACS User SetupConfiguring the AAA Server to Support WLAN Client Authentication Preparing the CiscoWorks WLSE for Managing WLAN DevicesStep 1 Log into the CiscoWorks WLSE Configuring the CiscoWorks WLSE advanced discovery options Configuring Advanced Discovery Options Access Point-Based WDS Solution ConfigurationConfiguring the WDS Access Point Using Automatic ConfigurationThese are the basic configuration tasks Configuring the Infrastructure Access Point infra-apconfig# username username password password Managing the Access Points with the CiscoWorks WLSEinfra-apconfig#hostname hostname infra-apconfig# ip domain-name ip domain-nameSwitch-Based WDS Solution Configuration Validating the ConfigurationConfiguring the Catalyst 6500 Supervisor Configuring the WDS on the WLSM Define AAA parameters for WLAN client authentication Configuring the Infrastructure Access Points wlsm# show wlccp wds ap Managing the WLSM and Access Points with the CiscoWorks WLSEValidating the Setup wlsm# show wlccp wnm statussup720# show mobility status mobility apFast Secure Roaming with CCKM When Using Multiple Encryption Types or VLANs Configuring ACU to use CCKM Step 2 Click Profile ManagementCisco SWAN Radio Management Features Preparing to Use Cisco SWAN Radio Management Cisco SWAN Radio Management Features enabled, the WDS periodically requests radio measurement data from supporting registered MNs. These MNs collect the requested data and send it to the WDS. The WDS aggregates data from the MNs and passes the aggregated data to the CiscoWorks WLSE. WLAN client monitoring is configured for client serving and non-serving channels Implementing the Cisco SWAN Framework Cisco Structured Wireless-Aware Network SWAN Implementation GuideCisco Structured Wireless-Aware Network SWAN Implementation Guide OL-6217-01