ENGLISH
3.10 Self-printing
When the power is turned on while the FEED switch is pressed, the printer will perform preset printing. After the
C B M 1 0 0 0
M P V 3 . x x
L P V 3 . x x
Serial Interface
Baud Rate : 19200 bps
Data Bit : 8 bits
Parity : None
Handshake : DTR/DSR
Buffer Size |
|
|
|
| |
4K bytes |
|
|
|
| |
Dip Switches |
|
|
|
| |
| DS1 |
|
|
|
|
| 1 2 3 4 5 6 7 | 8 |
| ||
ON | o | o |
|
| |
OFF | o o o o o |
|
| o |
Program & loader versions
Interface and its status (serial I/F in this example)
Buffer size
DIP switch status (DS3 for serial only)
| DS2 |
| 1 2 3 4 5 6 7 8 9 10 |
ON | o |
OFF | o o o o o o o o o |
| DS3 |
| 1 2 3 4 5 6 7 8 |
ON | o |
OFF o o o o o o o
! ” # $%& ’ ( ) * + ,
DEFGH I JKLMNOPQRSTUVWXYZ [ \ ] ^ _ ` a bc d e f g H i j k l mno pq r s t u vwx y z { } ~ . . . . . . . .
•
•
•All the printable characters are printed.
If the Auto Cutter is used, the paper is cut into pages each time a page is printed.
3.11 Hexadecimal Dump
1Hexadecimal dump function allows data sent from the host computer to be printed in hexadecimal numbers as well as in characters corresponding to the numbers.
2Starting hexadecimal dump
To start hex dump, turn the printer On while pressing and holding the FEED switch, with the printer cover left open. When you close the printer cover, the printer first prints “Hexadecimal Dump”, then prints all the subsequent data in hex and characters.
<Example of hexadecimal dump>
=== Hexadecimal Dump === |
|
| ||||||
To terminate hexadecimal dump, |
| |||||||
Press FEED switch three times. |
| |||||||
1B 40 73 | 6D 70 | 6C 65 | 0A | 30 | 31 | 32 | .@s amp l e . 0 1 | |
33 34 35 36 37 | 38 39 | 41 | 42 | 43 | 44 | 3456789ABCD | ||
45 46 47 | 48 49 | 4A | 4B | 4C | 4D 4F | 50 | EFGHI JKLMOP | |
51 52 53 | 54 55 | 56 57 58 | 59 | 5A | 0D | QRSTUVWXYZ . | ||
61 62 63 | 64 65 | 66 67 68 | 69 | 6A | 6B | a bcd e f gh i j k | ||
6C 6D 6E 6F 70 71 | 72 | 73 74 75 76 | l mnopq r s t u v | |||||
77 78 79 | 7A 0D | 0A | 0A | 0A |
|
|
| wxy z . . . . |
=== Completed ===
NOTE
•If a character is not available corresponding to the data received, “ . ” is printed instead.
•During hexadecimal dump, no other functions than DLE EOT and DLE ENQ work.
•If the data received is not enough for a full line, pressing the FEED switch causes the line to be printed.
3Quitting hexadecimal dump
The printer exits Hex Dump mode when it is turned off, the FEED switch is pressed 3 times consecutively, or the printer receives a Reset signal from the interface, after hex dump is completed.
— 20 —