2Printer Operation
Mode Settings
[Datamax® Emulation]
Top Menu | Sub Menu | Default | Menu | Remarks |
|
|
|
|
|
| Cover Open Sensor | Off | On | Sets the cover open sensor. |
| [Cover Sensor] |
| Off |
|
|
|
|
|
|
| Buzzer Select | Exec/Err | Exec/Err | Setting buzzer sounding conditions. |
|
|
| All |
|
|
|
| Error |
|
|
|
| Key |
|
|
|
| None |
|
|
|
|
|
|
| Metric/Inch | Inch | Inch | Sets the units. |
| [Metric/Inch Sel] |
| mm |
|
|
|
|
|
|
| Max Media Length | 10.00 inch | 1.00 to 50.00 inch | Sets the maximum media length. |
| [Max Media Len] | 254.0 mm | 25.4 to 1270.0 mm |
|
|
|
|
|
|
| Settings Lock | Off | On | Prevents a command changing the set value. |
|
|
| Off |
|
|
|
|
|
|
| Keyboard Lock | Off | On | Prevents a change by a key operation. |
|
|
| Off | Note: Hold down the Menu Key for at least 4 |
|
|
|
| seconds to enter the Menu Setup Mode when |
|
|
|
| setting the “On” menu. |
|
|
|
|
|
| Control Code | STD | STD | Switches command mode of DMX mode. |
|
|
| ALT |
|
|
|
|
|
|
| Emulation Select | DM4 | DM4 | Selects DataMax®/Zebra® compatibility |
| [Emulation Sel] |
| DMI | DM4: DataMax® 400 |
|
|
| DPP | DMI: DataMax® IClass |
|
|
| ZPI2 | DPP: DataMax® Prodigy Plus® |
|
|
|
| ZPI2: Zebra® 2844Z |
| Emulation Auto | On | On | Setting emulation (as above) auto detection. |
| Detect |
| Off |
|
| [Emulation Auto] |
|
|
|
|
|
|
|
|
After Print | AutoConfigure | On | On | Automatically configures optional devices. |
| [Auto Config] |
| Off | On .... AutoConfigure enabled (Regardless of |
|
|
|
| whether Function Select is set, if a |
|
|
|
| peeler or cutter is installed, each mode |
|
|
|
| is set automatically.) |
|
|
|
| Off ... AutoConfigure disabled (A peeler of |
|
|
|
| cutter is installed, but to not operate |
|
|
|
| the peeler or cutter, turn it Off and the |
|
|
|
| operation is selected by |
|
|
|
| Function Select.) |
|
|
|
|
|
| Function Select | Tear | Off | Selects the operation when the |
| [Function Sel] |
| Tear | AutoConfigure is set to Off. Designates the |
|
|
| Peel On* | paper position based on each option. The |
|
|
| Cut On** | operation of this device is enabled during |
|
|
| Rewind*** | selection. At the same time, the parameters of |
|
|
|
| the f command of Prodigy Plus are emulated |
|
|
|
| for each optional device. |
|
|
|
|
|
| Cutter Action | Backfeed | Backfeed | Sets the cutter action. |
|
|
| Through | With the optional AutoConfigure On, printing |
|
|
|
| is executed only when the cutter is installed |
|
|
|
| or only when Cut is selected by Function |
|
|
|
| Select. |
|
|
|
| Backfeed is always set after cutting. |
|
|
|
| Through is set at the rear end of sheets 1 to |
|
|
|
| |
|
|
|
| rear end of the final page of single sheet and |
|
|
|
| the copy is backfeed. |
*Only when peeling option is mounted. ** Only when cutter is mounted.
*** Only the Rewinder.
44