Printer Operation

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Mode Settings

 

 

 

 

[Zebra® Emulation]

Top Menu

Sub Menu

Default

Menu

Remarks

 

 

 

 

 

 

Paper Position

0.00 inch

Peel/Cut/Tear Off

Adjusts the stop position. It is based on the

 

 

0.00 mm

0.00 to 2.00 inch

inch/millimeter setting. There are initial

 

 

 

0.0 to 50.8 mm

values of the stop position for each device

 

 

 

Peel/Cut/Tear On

set above, and later, relative values are set.

 

 

 

-1.00 to 1.00 inch

 

 

 

 

-25.4 to 25.4 mm

 

 

 

 

 

 

 

Menu Key Action

Enters Menu

Enters Menu

Sets the menu key action.

 

 

 

Repeat Last One

Enters Menu:

 

 

 

 

Enters the menu setup mode.

 

 

 

 

Repeat Last One:

 

 

 

 

Last one is issued only for the final page.

 

 

 

 

In the case of a count, afterwards, only

 

 

 

 

last one is issued.

 

 

 

 

Note: Hold down the MENU key for at least 4

 

 

 

 

seconds in order to enter the Menu Setup

 

 

 

 

Mode when setting the “Repeat Last One”

 

 

 

 

menu.

 

 

 

 

 

Interfaces

RS-232C Baud

9600

115200

Setting the baud rate of the serial interface.

 

 

 

57600

• All settings related to the interfaceare

 

 

 

38400

enabled after the power is reconnected.

 

 

 

19200

 

 

 

 

9600

 

 

 

 

4800

 

 

 

 

2400

 

 

 

 

 

 

 

RS-232C Parity

None

None

Setting the communication parity for the

 

 

 

Odd

serial interface.

 

 

 

Even

 

 

 

 

 

 

 

RS-232C Length

8 bits

8 bits

Setting the character length for the serial

 

 

 

7 bits

interface.

 

 

 

 

 

 

RS-232C Stop bit

1 bit

1 bit

Setting the stop bit for the serial interface.

 

[RS-232C Stopbit]

 

2 bits

 

 

 

 

 

 

 

RS-232C X-ON

On Yes

On Yes

Selectively setting the X-ON flow control of

 

 

 

Off No

the serial interface.

 

 

 

 

 

 

IEEE1284

On

On

Setting both direction of the Centro

 

 

 

Off

Interface.

 

 

 

 

 

 

USB Device Class

Printer

Printer

Selects the USB device class.

 

[USB Device Clas]

 

VCOM

 

 

 

 

 

 

 

USB VCOM Protocol

Auto

Auto

Selects the protocol (flow control) when

 

[VCOM Protocol]

 

DTR

operating USB VCOM.

 

 

 

X-ON

 

Machine

Information

[Machine Info]

Model Number

CL-S***

Displays the model name.

 

 

 

 

Boot Version

*.*

Displays the boot version.

 

 

 

 

ROM Version

********

Displays the ROM version.

 

 

 

 

ROM Date

**/**/**

Displays the date the ROM was prepared.

 

 

 

 

ROM CheckSum

****

Displays the check sum of the ROM.

 

 

 

 

Head Check

OK

Displays the results of the head check.

 

 

NG

 

 

 

 

 

Print Counter

****.*** km

Displays the print counter.

 

 

 

 

Service Counter

****.*** km

Displays the service counter.

 

 

 

 

Sensor Monitor

*.* V

Displays the sensor level.

 

 

 

 

Option Interface

None

Displays the presence/absence of the

[Option I/F]

 

LAN

optional interface.

49