|
|
|
| Printer Operation |
|
|
|
|
|
|
|
|
|
|
|
|
|
| Mode Settings |
|
|
|
| [Datamax® Emulation] |
Top Menu | Sub Menu | Default | Menu | Remarks |
|
|
|
|
|
| Rewinder Auto | Off | On | |
| Online*** |
| Off | Sets the Rewinder Auto Online. |
| [Rew Auto Online] |
|
| In the case in which the setting is On, when |
|
|
|
| the Rewinder Open Error occurs, if the |
|
|
|
| Rewinder Cover is closed, it will automatically |
|
|
|
| return to Online and printing will restart. |
|
|
|
|
|
| Rewinder Online | 2 sec | 1 to 10 sec | |
| Delay*** |
|
| Sets the Rewinder Online Delay. |
| [Rew OnlineDelay] |
|
| Sets the time until the Rewinder restarts after |
|
|
|
| the Rewinder Cover is closed when the above |
|
|
|
| Rewinder Auto Online is On. |
|
|
|
|
|
| Rewinder Torque*** | 4 | 1 to 7 | |
|
|
|
| Sets the Rewinder Torque. |
|
|
|
|
|
| Peel Wait Delay** | 0.1 sec | 0.1 to 2.0 sec | Sets the Peel Wait Delay. |
|
|
|
| Displays only machines with a peeler |
|
|
|
| installed. |
Paper Position | 0.00 inch | Peel/Cut/Tear Off |
| 0.00 mm | 0.00 to 2.00 inch |
|
| 0.0 to 50.8 mm |
|
| Peel/Cut/Tear On |
|
| |
|
|
Adjusts the stop position. It is based on the inch/millimeter setting. There are initial values of the stop position for each device set above, and later, relative values are set.
| Menu Key Action | Enters Menu | Enters Menu | Sets the menu key action. |
|
|
| Repeat Last Set | Enters Menu: |
|
|
| Repeat Last One | Enters the menu setup mode. |
|
|
|
| Repeat Last Set: |
|
|
|
| Repeats the number of copies. |
|
|
|
| Repeat Last One: |
|
|
|
| Last one is issued only for the final page. |
|
|
|
| In the case of a count, afterwards, only |
|
|
|
| last one is issued. |
|
|
|
| Note: Hold down the MENU key for at least 4 |
|
|
|
| seconds in order to enter the Menu Setup |
|
|
|
| Mode when setting the “Repeat Last Set” or |
|
|
|
| “Repeat Last One” menus. |
|
|
|
|
|
Interfaces | 9600 | 115200 | Setting the baud rate of the serial interface. | |
|
|
| 57600 | • All settings related to the interface are |
|
|
| 38400 | enabled after the power is reconnected. |
|
|
| 19200 |
|
|
|
| 9600 |
|
|
|
| 4800 |
|
|
|
| 2400 |
|
| None | None | Setting the communication parity for the | |
|
|
| Odd | serial interface. |
|
|
| Even |
|
|
|
|
|
|
| 8 bits | 8 bits | Setting the character length for the serial | |
|
|
| 7 bits | interface. |
|
|
|
|
|
| 1 bit | 1 bit | Setting the stop bit for the serial interface. | |
|
| 2 bits |
| |
|
|
|
|
|
| On Yes | On Yes | Selectively setting the | |
|
|
| Off No | the serial interface. |
|
|
|
|
|
| IEEE1284 | On | On | Setting both direction of the Centro |
|
|
| Off | Interface. |
|
|
|
|
|
| USB Device Class | Printer | Printer | Selects the USB device class. |
| [USB Device Clas] |
| VCOM |
|
**Only when cutter is mounted.
***Only the Rewinder.
45