Wrist Strap, Belt Clip | Cobra Electronics MR HH415LI VP EU manual

Installation

Antenna, Wrist Strap and Belt Clip

Antenna, Wrist Strap and Belt Clip

•

Install Antenna

Antenna Installation

Wrist Strap

Belt Clip Secured to Belt

The flexible antenna is shipped separately in the package and must be attached before you use the radio.

1.Align the base of the antenna with the socket in the top of the radio.

2.Screw it all the way into the socket. Be sure that the seal seats properly.

NOTICE

Operating the radio without the antenna in place may damage the unit. The radio is not waterproof until the antenna and battery pack are in place with their seals properly seated.

Wrist Strap

The radio comes with the wrist strap already attached. It can be easily removed if you choose not to use it.

Insert Knob onto Belt Clip

Belt Clip

Use the spring-loaded belt clip to carry the radio on your person.

1.Press open the belt clip, slide it over the belt and release the clip.

2.Insert the round guide on the back of the radio into the guide channel on the back of the belt clip. The radio must be upside-down, as shown, to remove it from the belt clip.

3.Once the knob is inserted all the way into the belt clip channel, the radio swings free but remains secure.

Secure Radio

Nothing Comes Close to a Cobra® 25

Image 30

Cobra Electronics MR HH415LI VP EU owner manual Antenna, Wrist Strap and Belt Clip, Antenna Installation

Contents

MR HH415LI VP EU Our Thanks to You and Customer Assistance Radio Controls and Indicators LCD Backlit LCD Screen and Product Features Product Features Speaker/Mic Jack Table of Contents Important Safety Information Important Safety Information General Precautions Important Safety Information Recommendations for Marine Communication Recommendations for Marine Communication Canadian or U.S.A. Station License Licensing InformationStation License Radio Call Sign VHF Marine Radio Procedures Voice Calling Voice CallingVessel Corsair calling the vessel Vagabond Radiotelephone Calls Radiotelephone Calls Emergency Messages and Distress Procedure Emergency Messages and Distress Procedure Marine Emergency Signals If You Hear a Distress Call Say Marine Distress ProcedureTell where you are End message by saying For Example VHF Marine Channel Assignments Navigational Public Correspondence marine operatorPort Operations Digital Selective Calling USA International Distress, Safety and Calling 03A Government Only 156.900 21A U.S. Government Only Canada Coastguard Only 23A Government Only61A U.S. Government Only Canada Coastguard Only Channel 64A U.S. Government Only Canada Commercial Fishing Digital Selective Calling Voice communications not allowed Limits 81A U.S. Government Only Environmental Protection Operations Included in this Package Included in this Package Wrist Strap Antenna InstallationAntenna, Wrist Strap and Belt Clip Belt Clip Installing the Battery Pack Batteries and ChargerBatteries and Charger Initial Charge To Remove Battery Pack from Radio Alkaline Batteries Maintaining the Battery Charge Getting Started Power/Volume/Squelch Controls Power On/Off ControlVolume Control Common Radio Functions Squelch Control Talk Button To Display the Backlight Momentarily TRI-WATCH Button Call/Enter/Setup Button Preset ButtonBacklight/Key Lock Button Key Lock Scan Button High/Medium/Low H-M-L Power Button To Toggle Between H-M-L Power ModesCall /Enter/Setup Button To Set Personal Default Settings International/Canada/USA Channel Maps Setup Mode ProgrammingSetup Mode Programming To Set Channel Map Operating Area VibrAlert Mode To set VibrAlert Call Tone Mode To Set Call Tone To Set Roger Beep On or Off Roger Beep ModeKey Tone Mode To Set Key Tone On or Off Atis ID Programming Atis ID ProgrammingTo Set the Atis ID Number Atis ID Programming Marine Standby and Receive Rx Mode Standby/Receive and Transmit Transmit Tx Mode Standby/Receive TransmitTo Transmit a Message Advanced Operation Channel 16 ModeTo Switch to Channel Advanced Operation Tri-Watch Mode Tri-Watch Setup To Program or Edit the Tri-Watch Channels Using Tri-Watch Tri-Watch Scan Mode Tri-Watchmemory channels Memory Location Mode To Program Memory Locations To Exit Memory Location Mode To Recall a Stored Memory LocationTo Erase Stored Memory Locations Channel Scan Mode To Enter Channel Scan Memory Location Scan Mode To Enter Memory Location Scan From Marine Standby mode, press the MEM/ESC button Rewind-Say-Again Feature Using Rewind-Say-AgainExample Using Rewind-Say-Again to Record Audio Transmission Press Backlight MaintenanceTroubleshooting Key Lock button Specifications Specifications English Accessories AccessoriesLapel Speaker/Microphone Declaration of Conformity and CE Marking