Batteries and Charger | Cobra Electronics MR HH415LI VP EU instruction

Installation

Batteries and Charger

Batteries and Charger

•

Lithium-Ion Battery Pack

The radio is shipped with a sealed Lithium-Ion (LiON) battery pack (P/N CM 110-010) that is rechargeable.

WARNING

The charger provided for this radio is only to be used to charge the battery pack provided. Do Not charge any other type of batteries in the charger as fire, explosion or battery damage will occur. Avoiding extreme room temperatures will also help prolong the life of the battery pack for the radio.

When your rechargeable batteries begin to discharge too quickly, it is time to install a new battery pack. Your radio will also operate with six (6) high-quality AA alkaline batteries, using the AA alkaline battery tray (provided with this radio).

Install Battery Pack

Installing the Battery Pack

1.Position the battery pack to line up the two (2) external

alignment tabs to the alignment slots in the radio.

2. Engage the battery pack into the radio until battery pack is fully seated against the radio housing.

3. Pivot the locking tab up until it snaps into place on the back of the battery pack.

26 English

Image 31

Cobra Electronics MR HH415LI VP EU owner manual Batteries and Charger, Installing the Battery Pack

Contents

MR HH415LI VP EU Our Thanks to You and Customer Assistance LCD Radio Controls and Indicators Backlit LCD Screen and Product Features Speaker/Mic Jack Product Features Table of Contents Important Safety Information Important Safety Information General Precautions Important Safety Information Recommendations for Marine Communication Recommendations for Marine Communication Radio Call Sign Licensing InformationStation License Canadian or U.S.A. Station License VHF Marine Radio Procedures Voice Calling Voice CallingVessel Corsair calling the vessel Vagabond Radiotelephone Calls Radiotelephone Calls Emergency Messages and Distress Procedure Emergency Messages and Distress Procedure If You Hear a Distress Call Marine Emergency Signals End message by saying Marine Distress ProcedureTell where you are Say For Example VHF Marine Channel Assignments Digital Selective Calling Public Correspondence marine operatorPort Operations Navigational USA 03A Government Only International Distress, Safety and Calling 156.900 23A Government Only 21A U.S. Government Only Canada Coastguard Only61A U.S. Government Only Canada Coastguard Only Channel Digital Selective Calling Voice communications not allowed 64A U.S. Government Only Canada Commercial Fishing Limits 81A U.S. Government Only Environmental Protection Operations Included in this Package Included in this Package Belt Clip Antenna InstallationAntenna, Wrist Strap and Belt Clip Wrist Strap Batteries and Charger Installing the Battery PackBatteries and Charger Initial Charge Alkaline Batteries To Remove Battery Pack from Radio Maintaining the Battery Charge Common Radio Functions Power/Volume/Squelch Controls Power On/Off ControlVolume Control Getting Started Talk Button Squelch Control Key Lock TRI-WATCH Button Call/Enter/Setup Button Preset ButtonBacklight/Key Lock Button To Display the Backlight Momentarily Scan Button To Toggle Between H-M-L Power Modes High/Medium/Low H-M-L Power ButtonCall /Enter/Setup Button To Set Personal Default Settings To Set Channel Map Operating Area Setup Mode ProgrammingSetup Mode Programming International/Canada/USA Channel Maps To set VibrAlert VibrAlert Mode To Set Call Tone Call Tone Mode To Set Key Tone On or Off Roger Beep ModeKey Tone Mode To Set Roger Beep On or Off Atis ID Programming Atis ID ProgrammingTo Set the Atis ID Number Atis ID Programming Standby/Receive and Transmit Marine Standby and Receive Rx Mode Standby/Receive Transmit Transmit Tx ModeTo Transmit a Message Advanced Operation Channel 16 ModeTo Switch to Channel Advanced Operation Tri-Watch Setup To Program or Edit the Tri-Watch Channels Tri-Watch Mode Tri-Watchmemory channels Using Tri-Watch Tri-Watch Scan Mode To Program Memory Locations Memory Location Mode To Recall a Stored Memory Location To Exit Memory Location ModeTo Erase Stored Memory Locations To Enter Channel Scan Channel Scan Mode Memory Location Scan Mode From Marine Standby mode, press the MEM/ESC button To Enter Memory Location Scan Using Rewind-Say-Again Rewind-Say-Again FeatureExample Using Rewind-Say-Again to Record Audio Transmission Key Lock button MaintenanceTroubleshooting Press Backlight Specifications Specifications English Accessories AccessoriesLapel Speaker/Microphone Declaration of Conformity and CE Marking