Rules Operating, Product | Craftsman 315.22811 instruction

Owner'sManual

10in.

TABLE SAW

Model No. 315.228110

Save	this manual		for
future reference.
				•	Safety
_,	CAUTION:		Read and follow all	•	Features
	Safety	Rules	and Operating	• Assembly
	Instructions before first use of this			•	Operation
	product.			•	Operation
	product.			• Maintenance
				• Maintenance
Customer		Help Line: 1-800-932-3188		•	Parts List

Sears, Roebuck and Co., Hoffman	Estates,	IL 60179 USA	®
visit the Craftsman web page: www.sears.com/craftsman
972000-713
1-00

Page 1

Image 1

Craftsman 315.22811 owner manual Rules Operating, Instructions before first use of this, Product

Contents

Instructions before first use of this Rules OperatingProduct Rrftsmrn TABLESAW315.228110 Full ONE Year Warranty on Craftsman Table SAW 21-33 BladeCheckandBladeGuardAssembly3CRAFTSMANTABLESAW315.228110 Safety Alert Symbol SymbolRead ALL Instructions Do not USE in Dangerous Environ Never USE this Tool in AN Explosive USE a Support for the Sides and Back Before Making a CUT, be sure all adjust- merits are secureSave These INSTRUCTIONS. Refer to them Always Push the Workpiece never pull it toward the saw Extension Cords Speed and WiringElectrical Connection Grounding Instructions Rip Cut ResinSaw Blade Path Set Wide Table Kit Do not USE 7 in. Wobble Dadoes RRAFTSMIIN TABLESAW315.228110 Following items are included with your Table Saw 11CRRFTSMRNTABLESAW315.228110 L,*.l.,.l,L,J.l,l.,.I,*,l.*,l,,,I.,,I,.l.,,I.i WITH7/16in.SOCKETADJUSTABLE WrenchSocketwrench Combination Square Speed and Wiring Safety DevicesOperating Components 13CRRFTSMRNTABLESAW315.228110 Know Your Table SAW Bladeguard Blade Adjustinghandle BevelMiter Fenceholder Storage Brackets Lockingclamps Legstand Padlock Notprovided Off position before plugging tool into the powerTeeth Source Leveling feet Assembling LEG StandFiat washers 5/16 Hex nuts 5/16-18 NUT LEVELINGFOOT--HEX Storagebracketsupper Brace Lowerbrace Assembling Storage BracketsLegstandassembled Figure Hexbolt Mounting the LEG Stand on the Table SAW Base Endcap Frontrail Scale To Install Miter Table and FenceRAi Holdernut Hole B Tableslot Accessory To Install Accessory Table and RIP FenceLock Lever Smallhex To Install Blade GuardThroatplate Hexwrench Types of Cuts GroundingGroundingpin Coverofgrounded Outletbox Motor Cord CRRFTSI4RNTABLE SAW315.228110 CuI-rlNG Tips Throatplatebladeguard To Remove the Blade Bevelblade Locking Lever Adjusting HandleInnerandouterbladewasher Large Small HEX Wrench Remove the Throat Plate Loosen Nuts Riving Knife Guard AssemblyTocenterrivingknife Rearrangeshims Figure To Reduce Risk of Kickback It is weUworth using precautions to avoid the risksTo Avoid Kickback Use these guidelines to avoid kickback HOW to Mount a Featherboard HOW to Make a FeatherboardTo Make a Push Stick Featherboard To Adjust the Blade Angle To Adjust the Blade DepthAdjustinghandle RIP Fence Angledblade Miter Slidelock To Lock Miter TableMaking Cuts To Make a Straight Cross CUT To Make a Straight RIP CUT Blade Miterfence Guardassembly AdjustingclampPushstick Base Woodeninsert RIP Fence To Make a Bevel Cross CUTBevellockinglever Figure Do not lock To Make a Large Panel CUT Slidingmiteraccessory Tableassemblytable31CRRFTSMBNTABLESAW315,2281t0 Inarning Unplug the saw to avoid possible mlury To Make NON-THROUGH CutsRaise the saw blade by pushing the bevel locking Clamp Pushblock Bevellockinglever Figure Unplug your saw To Make Dado CutsAll blades must be rated For at least RPM Indicator Lockinglever Screws Locknut General MaintenanceBlade Adjusting Handle Bevelbevel Bolt Blade Socketadjustingwheel To Adjust the Bevel Locking LeverTo Check the Alignment of the RIP Fence to the Blade TAB Hexnut CAM Compression To Adjust the Accessory Table To Adjust the Front and Rear Rail ClampsTo Align the Miter Locking Clamps Replace the rails and check the rail cSamps 37CRRFTSMRNTABLESAW315.228110 CRRFTSMRNTABLESAW315.22811038 Eight screws are visible on the miter base B To Check Miter Fence AlignmentRRIIFTSMIIN TABLESAW315.228110 There are four slides located under the sliding To Adjust the Miter FenceHex nuts on top of the miter table Eccentric Screw UP Ofbase Slide Merindicator Miter Fence Zero To Adjust QUICK-STOPMiter Fence Degree Threaded Hole Bevel Gear Backupbracket Washer Locker Bracket AssemblyBlade Adjusting Handle CRRFTSHRNTABLESAW315.22811042 Tilt / Elevating Mechanism 43rlIAFTSMAW TABLESAW315.228110 Sliding miter table assembly does Adjust the rivingknife with shimsNot move smoothly Adjusted Blade is dull Saw does not make accurate 90 or 45 degree cuts Blade adjusting handle is hard to turn Saw does not startBlade makes poor cuts Motor labors in rip cut Craftsman 10 in. Table SAW Model no Forlegstandassembly Referto Rguref96,100 73 **STD501003 75 *STDe01005 48 **STD600803Screw Key Part Number Description Quan Description Quan 410 Key Part Number Description Quan661811-001 49CRAFTSMANTABLESAW315.228110 CRAFTSMANTABLESAW315.22811050 Key Part Number Description Quan Key Part Number Key Part NumberStandard Hardware Item --May Be Purchased Locally 503 Figuref Craftsman 10 in. Table SAW- Model no KEY Part Number Description Quan Parts List for Figure F HomeCentralso

Owner'sManual

TABLE SAW

Model No. 315.228110

Rules

and Operating

Instructions before first use of this

product.

Parts List

Sears, Roebuck and Co., Hoffman

Estates,

IL 60179 USA