Craftsman 10 in. Table SAW- Model no, Figuref

CRAFTSMAN 10 in. TABLE SAW- MODEL NO. 315.228110

3= I regardingThe modelyournumberTABLEwillSAWbe foundor whenon aorderingplate attachedrepair partsto the. side panel of the cabinet. Always mention the model number in all correspondence I1

=1=

m	6
(,9

FIGUREF

Page 52

Image 52

Craftsman 315.22811 owner manual Craftsman 10 in. Table SAW- Model no, Figuref

Contents

Instructions before first use of this Rules OperatingProduct Full ONE Year Warranty on Craftsman Table SAW Rrftsmrn TABLESAW315.228110 21-33 BladeCheckandBladeGuardAssembly3CRAFTSMANTABLESAW315.228110 Symbol Safety Alert SymbolRead ALL Instructions Do not USE in Dangerous Environ Never USE this Tool in AN Explosive Before Making a CUT, be sure all adjust- merits are secure USE a Support for the Sides and BackSave These INSTRUCTIONS. Refer to them Always Push the Workpiece never pull it toward the saw Speed and Wiring Extension CordsElectrical Connection Grounding Instructions Resin Rip CutSaw Blade Path Set Do not USE 7 in. Wobble Dadoes Wide Table Kit Following items are included with your Table Saw RRAFTSMIIN TABLESAW315.228110 11CRRFTSMRNTABLESAW315.228110 WITH7/16in.SOCKETADJUSTABLE Wrench L,*.l.,.l,L,J.l,l.,.I,*,l.*,l,,,I.,,I,.l.,,I.iSocketwrench Combination Square Safety Devices Speed and WiringOperating Components 13CRRFTSMRNTABLESAW315.228110 Blade Adjustinghandle Bevel Know Your Table SAW BladeguardMiter Fenceholder Storage Brackets Lockingclamps Legstand Off position before plugging tool into the power Padlock NotprovidedTeeth Source Assembling LEG Stand Leveling feetFiat washers 5/16 Hex nuts 5/16-18 NUT LEVELINGFOOT--HEX Assembling Storage Brackets Storagebracketsupper Brace LowerbraceLegstandassembled Figure Hexbolt Mounting the LEG Stand on the Table SAW Base To Install Miter Table and Fence Endcap Frontrail ScaleRAi Holdernut Hole B Tableslot Accessory To Install Accessory Table and RIP FenceLock Lever To Install Blade Guard SmallhexThroatplate Hexwrench Grounding Types of CutsGroundingpin Coverofgrounded Outletbox Motor Cord CuI-rlNG Tips CRRFTSI4RNTABLE SAW315.228110 Bevelblade Locking Lever Adjusting Handle Throatplatebladeguard To Remove the BladeInnerandouterbladewasher Large Small HEX Wrench Loosen Nuts Riving Knife Guard Assembly Remove the Throat PlateTocenterrivingknife Rearrangeshims Figure It is weUworth using precautions to avoid the risks To Reduce Risk of KickbackTo Avoid Kickback Use these guidelines to avoid kickback HOW to Make a Featherboard HOW to Mount a FeatherboardTo Make a Push Stick Featherboard To Adjust the Blade Depth To Adjust the Blade AngleAdjustinghandle RIP Fence Angledblade To Lock Miter Table Miter SlidelockMaking Cuts To Make a Straight Cross CUT Blade Miterfence Guardassembly Adjustingclamp To Make a Straight RIP CUTPushstick Base To Make a Bevel Cross CUT Woodeninsert RIP FenceBevellockinglever Figure Do not lock To Make a Large Panel CUT Slidingmiteraccessory Tableassemblytable31CRRFTSMBNTABLESAW315,2281t0 To Make NON-THROUGH Cuts Inarning Unplug the saw to avoid possible mluryRaise the saw blade by pushing the bevel locking Clamp Pushblock Bevellockinglever Figure To Make Dado Cuts Unplug your sawAll blades must be rated For at least RPM General Maintenance Indicator Lockinglever Screws LocknutBlade Adjusting Handle Bevelbevel Bolt To Adjust the Bevel Locking Lever Blade SocketadjustingwheelTo Check the Alignment of the RIP Fence to the Blade TAB Hexnut CAM Compression To Adjust the Front and Rear Rail Clamps To Adjust the Accessory TableTo Align the Miter Locking Clamps Replace the rails and check the rail cSamps 37CRRFTSMRNTABLESAW315.228110 CRRFTSMRNTABLESAW315.22811038 Eight screws are visible on the miter base B To Check Miter Fence AlignmentRRIIFTSMIIN TABLESAW315.228110 To Adjust the Miter Fence There are four slides located under the slidingHex nuts on top of the miter table Eccentric Screw UP Ofbase Slide To Adjust QUICK-STOP Merindicator Miter Fence ZeroMiter Fence Degree Locker Bracket Assembly Threaded Hole Bevel Gear Backupbracket WasherBlade Adjusting Handle CRRFTSHRNTABLESAW315.22811042 Tilt / Elevating Mechanism 43rlIAFTSMAW TABLESAW315.228110 Adjust the rivingknife with shims Sliding miter table assembly doesNot move smoothly Adjusted Blade is dull Blade adjusting handle is hard to turn Saw does not start Saw does not make accurate 90 or 45 degree cutsBlade makes poor cuts Motor labors in rip cut Craftsman 10 in. Table SAW Model no Forlegstandassembly Referto Rguref96,100 73 **STD501003 75 *STDe01005 48 **STD600803Screw Key Part Number Description Quan 410 Key Part Number Description Quan Description Quan661811-001 49CRAFTSMANTABLESAW315.228110 Key Part Number Description Quan CRAFTSMANTABLESAW315.22811050 Key Part Number Key Part NumberStandard Hardware Item --May Be Purchased Locally 503 Craftsman 10 in. Table SAW- Model no Figuref Parts List for Figure F KEY Part Number Description Quan HomeCentralso