To Adjust QUICK-STOP, Miter Fence, Degree

TO ADJUST QUICK-STOP

The quick-stop is preset at the factory to stop the miter fence at exactly zero degrees. However, when sliding miter table adjustments are made, these adjustments may cause the quick stop to need adjusting. Check quick-stop with miter scale set at

zero degrees. If adjustments are needed, proceed with the following steps:

•Loosen the eccentric screw holding the quick-stop.

•Place the quick-stop against the miter fence with miter scale set at zero degrees. See Figure 60.

•Adjust eccentric screw until it holds quick-stop securely against miter fence.

•Retighten hex nut, securing eccentric screw and quick-stop.

•Check your work. If the quick-stop is not at zero degrees, repeat steps 1-4.

M_ERINDICATOR

	MITER FENCE
ZERO	ADJUSTING CLAMP
DEGREE

MITER

FENCE

QUICK STOP AND
ECCENTRIC SCREW	Figure 60

41	CRAFTSMAN" TABLE SAW 315.228110

Page 41

Image 41

Craftsman 315.22811 To Adjust QUICK-STOP, Merindicator Miter Fence Zero, Degree, Quick Stop Eccentric Screw

Contents

Product Rules OperatingInstructions before first use of this Rrftsmrn TABLESAW315.228110 Full ONE Year Warranty on Craftsman Table SAW 3CRAFTSMANTABLESAW315.228110 BladeCheckandBladeGuardAssembly21-33 Safety Alert Symbol SymbolRead ALL Instructions Do not USE in Dangerous Environ Never USE this Tool in AN Explosive USE a Support for the Sides and Back Before Making a CUT, be sure all adjust- merits are secureSave These INSTRUCTIONS. Refer to them Always Push the Workpiece never pull it toward the saw Extension Cords Speed and WiringElectrical Connection Grounding Instructions Rip Cut ResinSaw Blade Path Set Wide Table Kit Do not USE 7 in. Wobble Dadoes RRAFTSMIIN TABLESAW315.228110 Following items are included with your Table Saw 11CRRFTSMRNTABLESAW315.228110 L,*.l.,.l,L,J.l,l.,.I,*,l.*,l,,,I.,,I,.l.,,I.i WITH7/16in.SOCKETADJUSTABLE WrenchSocketwrench Combination Square Speed and Wiring Safety DevicesOperating Components 13CRRFTSMRNTABLESAW315.228110 Know Your Table SAW Bladeguard Blade Adjustinghandle BevelMiter Fenceholder Storage Brackets Lockingclamps Legstand Padlock Notprovided Off position before plugging tool into the powerTeeth Source Leveling feet Assembling LEG StandFiat washers 5/16 Hex nuts 5/16-18 NUT LEVELINGFOOT--HEX Storagebracketsupper Brace Lowerbrace Assembling Storage BracketsLegstandassembled Figure Hexbolt Mounting the LEG Stand on the Table SAW Base Endcap Frontrail Scale To Install Miter Table and FenceRAi Holdernut Lock Lever To Install Accessory Table and RIP FenceHole B Tableslot Accessory Smallhex To Install Blade GuardThroatplate Hexwrench Types of Cuts GroundingGroundingpin Coverofgrounded Outletbox Motor Cord CRRFTSI4RNTABLE SAW315.228110 CuI-rlNG Tips Throatplatebladeguard To Remove the Blade Bevelblade Locking Lever Adjusting HandleInnerandouterbladewasher Large Small HEX Wrench Remove the Throat Plate Loosen Nuts Riving Knife Guard AssemblyTocenterrivingknife Rearrangeshims Figure To Reduce Risk of Kickback It is weUworth using precautions to avoid the risksTo Avoid Kickback Use these guidelines to avoid kickback HOW to Mount a Featherboard HOW to Make a FeatherboardTo Make a Push Stick Featherboard To Adjust the Blade Angle To Adjust the Blade DepthAdjustinghandle RIP Fence Angledblade Miter Slidelock To Lock Miter TableMaking Cuts To Make a Straight Cross CUT To Make a Straight RIP CUT Blade Miterfence Guardassembly AdjustingclampPushstick Base Woodeninsert RIP Fence To Make a Bevel Cross CUTBevellockinglever Figure Do not lock 31CRRFTSMBNTABLESAW315,2281t0 Slidingmiteraccessory TableassemblytableTo Make a Large Panel CUT Inarning Unplug the saw to avoid possible mlury To Make NON-THROUGH CutsRaise the saw blade by pushing the bevel locking Clamp Pushblock Bevellockinglever Figure Unplug your saw To Make Dado CutsAll blades must be rated For at least RPM Indicator Lockinglever Screws Locknut General MaintenanceBlade Adjusting Handle Bevelbevel Bolt Blade Socketadjustingwheel To Adjust the Bevel Locking LeverTo Check the Alignment of the RIP Fence to the Blade TAB Hexnut CAM Compression To Adjust the Accessory Table To Adjust the Front and Rear Rail ClampsTo Align the Miter Locking Clamps Replace the rails and check the rail cSamps 37CRRFTSMRNTABLESAW315.228110 CRRFTSMRNTABLESAW315.22811038 RRIIFTSMIIN TABLESAW315.228110 To Check Miter Fence AlignmentEight screws are visible on the miter base B There are four slides located under the sliding To Adjust the Miter FenceHex nuts on top of the miter table Eccentric Screw UP Ofbase Slide Merindicator Miter Fence Zero To Adjust QUICK-STOPMiter Fence Degree Threaded Hole Bevel Gear Backupbracket Washer Locker Bracket AssemblyBlade Adjusting Handle CRRFTSHRNTABLESAW315.22811042 Tilt / Elevating Mechanism 43rlIAFTSMAW TABLESAW315.228110 Sliding miter table assembly does Adjust the rivingknife with shimsNot move smoothly Adjusted Blade is dull Saw does not make accurate 90 or 45 degree cuts Blade adjusting handle is hard to turn Saw does not startBlade makes poor cuts Motor labors in rip cut 96,100 Forlegstandassembly Referto RgurefCraftsman 10 in. Table SAW Model no Screw 48 **STD60080373 **STD501003 75 *STDe01005 Key Part Number Description Quan Description Quan 410 Key Part Number Description Quan661811-001 49CRAFTSMANTABLESAW315.228110 CRAFTSMANTABLESAW315.22811050 Key Part Number Description Quan Key Part Number Key Part NumberStandard Hardware Item --May Be Purchased Locally 503 Figuref Craftsman 10 in. Table SAW- Model no KEY Part Number Description Quan Parts List for Figure F HomeCentralso

Craftsman 315.22811 owner manual To Adjust QUICK-STOP, Merindicator Miter Fence Zero, Degree

Models: 315.22811

TO ADJUST QUICK-STOP

M_ERINDICATOR

MITER FENCE

ZERO

DEGREE

MITER

FENCE

QUICK STOP AND

ECCENTRIC SCREW